Ceiling GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer.
Use minimum 90°c supply conductors.
This instruction shows a typical installation.
1A 5
4
MOUNTING PLATE
1 MOUNTING PLATE STUD
2 MOUNTING PLATE SCREW
FIXTURE BASE
6
SOCKET LAMP
7 FIXTURE THUMB SCREW
8
8
1 1
Secure the mounting plate to the electrical box with two mounting plate screws provided with electrical box.
2
Partially thread the two mounting plate studs into the mounting plate.
3
Connect the fixture to a suitable ground in accordance to local electrical codes.
4
Connect the white fixture wire (square and/or rigid) to the neutral power line wire with a wire nut.
5
Connect the black fixture wire (round and/or smooth) to the hot power line wire with a wire nut.
6
Align the key slots on the fixture base to the mounting plate studs, place the fixture base onto the mounting plate, secure it by rotating it to the narrow portion of the keyed slot, and tighten the mounting studs until the fixture base is flush with the ceiling.
7
Screw the lamp(s) into the socket(s). Refer to the label on the lamp socket for Max Wattage information.
8
Install the fixture by aligning it with the fixture base, then using the thumb screws to secure it in place. 1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A 5
4
PLAQUE DE MONTAGE
1 GOUJON DE MONTAGE
2 VIS DE MONTAGE
BASE DU LUMINAIRE
6
DOUILLE AMPOULE
7 LUMINAIRE VIS DE POUCE
8
8
1 1
Fixer la plaque de montage à la boîte électrique avec deux vis de montage fournis avec le boîtier électrique.
2
Visser partiellement les deux tiges filetées de fixation dans la plaque de montage.
3
Connecter le luminaire à un terrain approprié conformément aux codes électriques locaux.
4
Connecter le fil blanc du luminaire au fil de ligne à neutre avec un écrou de fil.
5
Connecter le fil noir du luminaire au fil ligne électrique chaud avec un serre-fils.
6
Alignez les fentes clés sur le luminaire de base pour les vis de montage, placez le luminaire sur la plaque de montage, fixez-le en le tournant à la partie étroite de la fente à clé et serrer les goujons de fixation jusqu'à ce que la base de le luminaire est en affleurement avec le plafond.
7
Visser les ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de lampe Puissance max pour plus d'informations.
8
Installer le luminaire en alignant sur la base de le luminaire, puis en utilisant les vis de pouce pour le fixer en place.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A 5
4
PLACA DE MONTAJE
1 ESPARRAGO DE MONTAJE
2 TORNILLO DE MONTAJE
BASE DE LA LÁMPARA
6
ENCHUFE BOMBILLA
7 LÁMPARA TORNILLO DE PULGAR
8
8
1 1
Fije la placa de montaje a la caja eléctrica con dos tornillos de montaje suministrados con la caja eléctrica.
2
Enrosque parcialmente los dos pernos de montaje en la placa de montaje.
3
Conecte la lámpara a una puesta a tierra adecuada de acuerdo a los códigos eléctricos locales.
4
Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con un tapón de alambre.
5
Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre.
6
Alinee las ranuras en el base de la lámpara para los esparragos de montaje, coloque el base sobre la placa de montaje de la lámpara, fíjelo girándolo a la porción angosta de la ranura de la llave y apriete los esparrago de montaje hasta la base de la lámpara esté al ras con el techo.
7
Atornille las bombillas en los enchufes. Consulte la etiqueta en el enchufe de la lámpara para obtener información de Max Wattage.
8
Instale la lámpara al base de la lámpara y luego utilizando los tornillos de pulgar para fijarlo en su lugar.
Secure the mounting plate to the junction box. ... Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the ...
á. Conecte el cable negro de la l mpara al cable de alimentación de línea caliente con un tapón de alambre. á. Alinee las ranuras en el base de la l mpara para ...
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 4. 1. 1.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut. Place the decorative cup ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
the applicable installation code by a person familiar with the ... Use minimum 90°c supply conductors. 4. 1. 2. 3. 3. 4. CAP NUT. THREADED NIPPLE. 3 ...
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...
Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threaded pipe and secure it in place with the washer and hex nut ...
Cadence 2 Light Flush Mount. 1.1. FM390. Ceiling. FM390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC ...
Installation Instructions for. Hamlet 2 Light Semi-Flush Mount. 1.0. SF325. SF325. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
Place the shade inside of the decorative ring and secure it in place using the tabs, then close and secure the decorative ring using the thumb screw. 1. 2. 1A. 1.
Installation Instructions for ... Feed the fixture wires through the stem assembly and screw the stem ... box, place the canopy onto the mounting plate, and secure it in place with the ... Refer to the label on the lamp socket for Max Wattage informa
Connect the fixture to a suitable ground in accordance with local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut.