These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is suitable for damp locations.
Use minimum 90°c supply conductors.
This product is listed by one of the following “Nationally Recognized Testing Laboratory”
This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
1A 5
4
MOUNTING PLATE
1
THREADED PIPE
FIXTURE BASE
CAP NUT
6 7 LAMP
1
If necessary, screw the shorter end of the threaded pipe to the mounting plate.
2
Secure the mounting plate to the junction box.
3
Connect the fixture to a suitable ground in accordance to local electrical codes.
4
Connect the white fixture wire to the neutral power line wire with a wire nut.
5 1
Connect the black fixture wire to the hot power line wire with a wire nut.
6
Place the fixture base onto the threaded pipe and secure it in place by screwing the cap nut onto the threaded pipe.
7
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
1
1.0
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c. 1A 5
4
PLAQUE DE MONTAGE
1
TUYAU FILETÉ
BASE DE LUMINAIRE
ECROU CAPUCHON
6 7 AMPOULE
1
Si nécessaire, visser l'extrémité la plus courte de tuyau fileté à la plaque de montage.
2
Fixer la plaque de montage sur le boîte de jonction.
3
Connecter le luminaire à un terrain approprié conformément aux codes électriques locaux.
4
Connecter le fil blanc de luminaire pour le fil de ligne à neutre avec un écrou de fil.
5 1
Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
6
Placez la base de luminaire sur le tuyau fileté et fixez-le en place en vissant l'écrou capuchon sur le tuyau fileté.
7
Visser l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de lampe pour obtenir des informations Max Puissance.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min. 1A 5
4
PLACA DE MONTAJE
1
TUBO ROSCADO
BASE DE LA LÁMPARA
TUERCA CAPUCHON
6 7 BOMBILLA
1
Si es necesario, atornillar el extremo más corto del tubo roscado a la placa de montaje.
2
Fije la placa de montaje a la caja eléctrica.
3
Conecte la lámpara a una puesta a tierra adecuada de acuerdo a los códigos eléctricos locales.
4
Conecte el cable blanco de la lámpara al cable de la línea de alimentación neutra con una tuerca para cable.
5
Conecte el cable negro de la lámpara al cable de la línea eléctrica caliente con una tuerca para cable.
6
Coloque la base de la lámpara en el tubo roscado y seguro en su lugar enroscando la tuerca capuchon en el tubo roscado.
7
Atornille las bombillas en los enchufes. Consulte la etiqueta del enchufe para obtener información Max Potencia.
3
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077 800.323.3226 - 847.626.6300
Connect the fixture to a suitable ground in accordance with local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut.
Colorado Springs 1 Light Pendant. 1.2. P1390. Pendant. P1390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant. NEC junction boxes. This product is safety listed for damp locations. This product may
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 4. 1. 1.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut. Place the decorative cup ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
the applicable installation code by a person familiar with the ... Use minimum 90°c supply conductors. 4. 1. 2. 3. 3. 4. CAP NUT. THREADED NIPPLE. 3 ...
Secure the mounting plate to the junction box. ... Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the ...
Colorado Springs 6 Light Foyer. 1.1. F3046-6. Foyer. F3046/6. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product
G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandescent dimmer. This instru
Placez la coupe sur le tuyau fileté et fixez-le en place en vissant le fleuron sur le tuyau fileté. 4. 5. AMPOULE. ATTENTION RISQUE INCENDIE. : D'. Ce produit ...
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations. This product may be dimmed ...
á. Conecte el cable negro de la l mpara al cable de alimentación de línea caliente con un tapón de alambre. á. Alinee las ranuras en el base de la l mpara para ...
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...
