Ceiling GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer.
Use minimum 90°c supply conductors.
This instruction shows a typical installation.
1A
1
MOUNTING PLATE
THREADED NIPPLE
2
FIXTURE BASE
LAMP
4 3 WASHER
NUT CAP NUT
5
THUMB SCREW SHADE
5
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Place the fixture base and washer over the threaded nipple, then secure them in place by tightening the nut.
3
Screw the cap nut onto the threaded nipple.
4
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
5 1
Install the shade onto the fixture base and secure it in place using the thumb screws.
1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A
1
PLAQUE DE MONTAGE
ATTACHE FILETE
2
BASE DE LUMINAIRE
AMPOULE
3 RONDELLE
ECROU ECROU DE CASQUETTE
5
VIS DE POUCE ABAT-JOUR
1
5
2
Reportez-vous aux instructions pour supplément clos électrique et installation de luminaire sur boîte de sortie de maison. . Placer la base de le luminaire et la rondelle sur le attache fileté, puis fixez-les en place en serrant l'écrou.
3
Vissez l'écrou de casquette sur le attache fileté.
4
Vissez les ampoules dans les douilles. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
5 1
Installer l'abat-jour sur le base de le luminaire et fixez-le à l'aide des vis de pouce.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A
1
PLACA DE MONTAJE
CONECTADOR ROSCADO
2
BASE DE LA LÁMPARA
BOMBILLA
3 ARANDELA
TUERCA TUERCA DE TAPA
5
TORNILLO DE PULGAR PANTALLA
5 1
1
Siga las instrucciones de Instalación incluido suplemento para eléctricos e instalación del accesorio en la caja de enchufe de casa.
2
Coloque el base de la lámpara y la arandela sobre el conectador roscado, y fíjelos en su lugar apretando la tuerca.
3
Atornille la tuerca de tap en el conecatador roscado.
4
Enrosque las bombillas en los enchufes. Consulte la etiqueta en el zócalo de la lámpara para obtener información de Max Wattage.
5 1
Instale la pantalla sobre la base de la lámpara y asegúrelo en su lugar utilizando los tornillos de pulgar.
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...
Cadence 2 Light Flush Mount. 1.1. FM390. Ceiling. FM390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC ...
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Marquer les emplacements des trous d'ancre sur la plaque de montage et ... Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un ...
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Lennon 5 Light Semi-Flush Mount. 1.0. SF340. SF340. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
Secure the mounting plate to the junction box. ... Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the ...
Place the shade inside of the decorative ring and secure it in place using the tabs, then close and secure the decorative ring using the thumb screw. 1. 2. 1A. 1.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 4. 1. 1.
á. Conecte el cable negro de la l mpara al cable de alimentación de línea caliente con un tapón de alambre. á. Alinee las ranuras en el base de la l mpara para ...
Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threaded pipe and secure it in place with the washer and hex nut ...
Conecte el cable blanco de la lámpara al cable de lÃnea de energÃa neutra con una tuerca para cable. Conecte el cable negro de la lámpara al cable de lÃnea ...
Installation Instructions for. Hamlet 2 Light Semi-Flush Mount. 1.0. SF325. SF325. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
Placez la coupe sur le tuyau fileté et fixez-le en place en vissant le fleuron sur le tuyau fileté. 4. 5. AMPOULE. ATTENTION RISQUE INCENDIE. : D'. Ce produit ...
Install the glass panels by carefully sliding them into the housing and securing ... Connect the white fixture wire to the neutral power line wire with a wire nut.