Ceiling GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer.
Use minimum 90°c supply conductors.
This instruction shows a typical installation.
1A
2
MOUNTING PLATE
1
THREADED NIPPLE
FIXTURE BASE
7
LAMP WASHER
COUPLER
8
THREADED PIPE
9
SHADE
9
CUP
FINIAL 1
If necessary, screw the shorter end of the threaded nipple tightly onto the mounting plate.
2
Secure the mounting plate to the electrical box with two mounting plate screws.
3
Connect the fixture to a suitable ground in accordance to local electrical codes.
4
Connect the white fixture wire to the neutral power line wire with a wire nut.
5 1
Connect the black fixture wire to the hot power line wire with a wire nut.
6
Place the fixture base and washer over the threaded nipple, then secure them in place by fastening the coupler.
7
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
8
Screw the threaded pipe onto the coupler.
9
Place the shade and cup over the threaded pipe, then secure them in place by tightening the finial.
1
1.2
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A
2
PLAQUE DE MONTAGE
1
ATTACHE FILETE
BASE DE LUMINAIRE
7
AMPOULE RONDELLE
COUPLER
8
TUYAU FILETÉ
9
ABAT-JOUR
9
COUPE
FLEURON 1
Si nécessaire, visser l'extrémité plus courte du attache fileté fermement sur la plaque de montage.
2
Fixer la plaque de montage sur le boîte électrique avec deux vis de montage.
3
Connecter le luminaire à un terrain approprié conformément aux codes électriques locaux.
4
Connecter le fil blanc du luminaire (carré et / ou rigide) pour le fil de ligne à neutre avec un écrou de fil.
5 1
Connecter le fil noir du luminaire (rond et / ou lisse) au fil de la ligne d'alimentation hot avec un écrou de fil.
6
Placez la base de luminaire et la rondelle sur le attache fileté, puis fixez-les en place en fixant le coupleur.
7
Vissez les ampoules dans les douilles. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
8
Vissez la tuyau fileté sur le coupleur.
9
Placez l'abat-jour et coupe sur la tuyau fileté, puis fixez-les en place en serrant le fleuron.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A
2
PLACA DE MONTAJE
1
CONECTADOR ROSCADO
BASE DE LA LÁMPARA
7
BOMBILLA ARANDELA
ACOPLADOR
8
TUBO ROSCADO
9
PANTALLA
9
COPA
1 FINIAL
1
Si es necesario, atornille el extremo corto de el conectador roscado firmemente sobre la placa de montaje.
2
Fije la placa de montaje a la caja eléctrica con dos tornillos de montaje.
3
Conecte la lámpara a una puesta a tierra adecuada de acuerdo a los códigos eléctricos locales.
4
Conecte el cable blanco de la lámpara (cuadrado y / o rígido) al cable de la línea de alimentación neutra con una tuerca para cable.
5 1
Conecte el cable negro de la lámpara (redonda y / o suave) al cable de la línea eléctrica caliente con una tuerca para cable.
6
Coloque el base de la lámpara y la arandela sobre el conectador roscado, luego bloquéelas sujetando el acoplador.
7
Atornille las lámparas en los enchufes. Consulte la etiqueta en el enchufe de la lámpara para obtener información de Max Wattage.
8
Enrosque el tubo roscado en el acoplador.
9
Coloque la pantalla y copa sobre el tubo roscado, luego fijarlos en su sitio apretando el finial.
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...
Cadence 2 Light Flush Mount. 1.1. FM390. Ceiling. FM390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC ...
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Marquer les emplacements des trous d'ancre sur la plaque de montage et ... Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un ...
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Lennon 5 Light Semi-Flush Mount. 1.0. SF340. SF340. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
Secure the mounting plate to the junction box. ... Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the ...
Place the shade inside of the decorative ring and secure it in place using the tabs, then close and secure the decorative ring using the thumb screw. 1. 2. 1A. 1.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 4. 1. 1.
á. Conecte el cable negro de la l mpara al cable de alimentación de línea caliente con un tapón de alambre. á. Alinee las ranuras en el base de la l mpara para ...
Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threaded pipe and secure it in place with the washer and hex nut ...
Conecte el cable blanco de la lámpara al cable de lÃnea de energÃa neutra con una tuerca para cable. Conecte el cable negro de la lámpara al cable de lÃnea ...
Installation Instructions for. Hamlet 2 Light Semi-Flush Mount. 1.0. SF325. SF325. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
Placez la coupe sur le tuyau fileté et fixez-le en place en vissant le fleuron sur le tuyau fileté. 4. 5. AMPOULE. ATTENTION RISQUE INCENDIE. : D'. Ce produit ...
