Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes.
Use minimum 90°c supply conductors.
This product is safety listed for damp locations.
1A 1
LAMP
2
THREADED PIPE
4
SHADE
SHADE RING DIFFUSER WASHER HEX NUT 5
CUP FINIAL
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Screw the threaded pipe to the bottom of the fixture.
3
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
4
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten).
5
Place the cup onto the threaded pipe and secure it in place by screwing the finial onto the threaded pipe.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A 1
AMPOULE
2
TUYAU FILETÉ
4
ABAT-JOUR
ANNEAU D’ABAT-JOUR DIFFUSEUR RONDELLE ECROU HEX 5
COUPE FLEURON
1
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et luminaire sur une boîte de sortie de la maison.
2
Vissez le tuyau fileté à l'ensemble de douille.
3
Vissez l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de lampe pour obtenir des informations Max Puissance.
4
Placez l'abat-jour, anneau d’abat-jour, diffuseur, et rondelle (dans cet ordre) sur le tuyau fileté et fixez-le en place avec l'écrou hexagonal (Ne pas trop serrer).
5
Placez la coupe sur le tuyau fileté et fixez-le en place en vissant le fleuron sur le tuyau fileté.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A 1
BOMBILLA
2
TUBO ROSCADO
4
PANTALLA
ANILLO DE LA PANTALLA DIFUSOR ARANDELA TUERCA HEX 5
COPA FINIAL
1
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de salida de casa.
2
Enrosque el tubo roscado a la asamblea de enchufe.
3
Atornille las bombillas en los enchufes. Consulte la etiqueta en el casquillo de la lámpara para obtener información Max Potencia.
4
Coloque la pantalla, anillo de la pantalla, difusor, y arandela (en ese orden) en el tubo roscado y seguro en su lugar con la tuerca hexagonal (No apriete demasiado).
5
Coloque la copa en el tubo roscado y seguro en su lugar atornillando el finial en el tubo roscado.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Marquer les emplacements des trous d'ancre sur la plaque de montage et ... Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un ...
Lennon 5 Light Semi-Flush Mount. 1.0. SF340. SF340. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...
Placez la coupe sur le tuyau fileté et fixez-le en place en vissant le fleuron sur le tuyau fileté. 4. 5. AMPOULE. ATTENTION RISQUE INCENDIE. : D'. Ce produit ...
Cadence 2 Light Flush Mount. 1.1. FM390. Ceiling. FM390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC ...
Installer et fixer la chaîne de perles en les accrochant au haut et au bas de ... le bas de l'appareil et à la police, puis accrocher la basse chaîne de perles à la.
Ensure that the spun pan rests properly on top of the shade. Screw the ... with the construction and operation of the product .... A Generation Brands Company.
Follow enclosed supplement installation instructions for electrical and fixture installation onto junction box. Screw the lamps into ... A Generation Brands Company.
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes . Consulte la etiqueta del casquillo de la lámpara para obtener información Max.
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 2. POST. POST SCREW. 3. 4. 4. GL
Connect the black fixture wire to the hot power line wire with a wire nut. ... Refer to the label on the lamp socket for Max Wattage information. Install the glass ...
Connect the white fixture wire to the neutral power line wire with a wire nut. Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws. Install th
Conecte el cable blanco de la lámpara al cable de lÃnea de energÃa neutra con una tuerca para cable. Conecte el cable negro de la lámpara al cable de lÃnea ...