Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threaded pipe and secure it in place with the washer and hex nut ...
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes.
Use minimum 90°c supply conductors.
This product is safety listed for damp locations.
1A
1
LAMP 3
3 2
THREADED PIPE
4
SHADE
WASHER HEX NUT 5
CUP FINIAL
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Screw the threaded pipe to the bottom of the fixture.
3
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
4
Place the shade onto the threaded pipe and secure it in place with the washer and hex nut (Do not over tighten).
5
Place the cup onto the threaded pipe and secure it in place by screwing the finial onto the threaded pipe.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
1
AMPOULE 3
3 2
TUYAU FILETÉ
4
ABAT-JOUR
RONDELLE ECROU HEX 5
COUPE FLEURON
1
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et luminaire sur une boîte de sortie de la maison.
2
Vissez le tuyau fileté à l'ensemble de douille.
3
Vissez l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de lampe pour obtenir des informations Max Puissance.
4
Placez l'abat-jour sur le tuyau fileté et fixez-le en place avec la rondelle et écrou hexagonal (Ne pas trop serrer).
5
Placez la coupe sur le tuyau fileté et fixez-le en place en vissant le fleuron sur le tuyau fileté.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
1
BOMBILLA 3
3 2
TUBO ROSCADO
4
PANTALLA
ARANDELA TUERCA HEX 5
COPA
FINIAL 1
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de salida de casa.
2
Enrosque el tubo roscado a la asamblea de enchufe.
3
Atornille las bombillas en los enchufes. Consulte la etiqueta en el casquillo de la lámpara para obtener información Max Potencia.
4
Coloque la pantalla sobre el tubo roscado y seguro en su lugar con la arandela y la tuerca hex (No apriete demasiado).
5
Coloque la copa en el tubo roscado y seguro en su lugar atornillando el remate en el tubo roscado.
Secure the mounting plate to the junction box. ... Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the ...
P1415. Place the shade onto the socket and secure it in place by screwing the collar nut onto the socket using the shade tool. ... A Generation Brands Company.
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...
á. Conecte el cable negro de la l mpara al cable de alimentación de línea caliente con un tapón de alambre. á. Alinee las ranuras en el base de la l mpara para ...
Cadence 2 Light Flush Mount. 1.1. FM390. Ceiling. FM390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC ...
Installation Instructions for. Hamlet 2 Light Semi-Flush Mount. 1.0. SF325. SF325. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 4. 1. 1.
Place the shade inside of the decorative ring and secure it in place using the tabs, then close and secure the decorative ring using the thumb screw. 1. 2. 1A. 1.
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Connect the fixture to a suitable ground in accordance with local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Marquer les emplacements des trous d'ancre sur la plaque de montage et ... Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un ...
1A. 3. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards ... Connecter le fil noir du luminaire (rond et
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut. Place the decorative cup ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
Lennon 5 Light Semi-Flush Mount. 1.0. SF340. SF340. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...