Connect the fixture to a suitable ground in accordance with local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut.
Ceiling GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations. This instruction shows a typical installation.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Use minimum 90°c supply conductors.
1A
A
7
B
JUNCTION BOX
6
MOUNTING PLATE STUD MOUNTING PLATE CANOPY
SWIVEL
SWIVEL SCREW
CAP NUT
8
8 X12 X12
1 A
B
A
B A
B
A
B
B
A
4 B
A
4
B
A
B
A
B
A
STRAND
A
B
A
B
A
B
1
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
2
Secure the mounting plate to the junction box.
3
Feed the fixture wires through the swivel and canopy, then screw the canopy onto the fixture and tighten the swivel screw.
4
Temporarily place the fixture sideways and install the strands according to the diagrams provided.
5
Connect the fixture to a suitable ground in accordance with local electrical codes.
6
Connect the white fixture wire to the neutral power line wire with a wire nut.
7
Connect the black fixture wire to the hot power line wire with a wire nut.
8
Neatly place all the wires into the junction box, place the canopy onto the mounting plate studs, and secure it in place with two cap nuts. 1
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c. 1A
A
7
B
BOÎTE DE JONCTION
6
GOUJON DE MONTAGE PLAQUE DE MONTAGE DAIS
PIVOT
VIS DE PIVOT
ECROU CAPUCHON
8
8 X12 X12
1 A
B
A
B A
B
A
B
B
A
4 B
A
4
B
A
B
A
B
A
BRIN
A
B
A
B
A
B
1
Visser l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de lampe pour obtenir des informations Max Puissance.
2
Fixez la plaque de montage à la boîte de jonction.
3
Nourrir les fils de luminaire à travers le pivot et la dais, puis vissez la dais sur le luminaire et serrer la vis de pivot.
4
Placez temporairement le luminaire sur le côté et installer les brins selon les schémas fournis.
5
Connectez le luminaire à un terrain approprié conformément aux codes électriques locaux.
6
Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un écrou de fil.
7
Connectez le fil noir de luminaire au fil de la ligne d'alimentation chaude avec un écrou de fil.
8
Soigneusement placer tous les fils dans la boîte de jonction, placer la dais sur les goujons de montage et fixez-le en place avec deux écrous capuchon.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min. 1A
A
7
B
CAJA DE JUNCTURA
6
ESPARRAGO DE MONTAJE PLACA DE MONTAJE DOSEL
GIRATORIO
TORNILLO DEL GIRATORIO
TUERCA CAPUCHON
8
8 X12 X12
1 A
B
A
B A B
A
B
B
A
4 B
A
4
B
A
B
A
B
A
STRAND
A
B
A
B
A
B
1
Atornille las bombillas en los enchufes. Consulte la etiqueta en el casquillo de la lámpara para obtener información Max Potencia.
2
Fije la placa de montaje a la caja de conexiones.
3
Pase los cables de la lámpara a través del giratorio y dosel, luego atornille el dosel en la lámpara y apriete el tornillo giratorio.
4
Temporalmente coloque la lámpara de lado y instalar las hebras de acuerdo con los diagramas proporcionados.
5
Conecte la lámpara a una tierra adecuada, de acuerdo con los códigos eléctricos locales.
6
Conecte el cable blanco de la lámpara al cable de línea de energía neutra con una tuerca de cable.
7
Conecte el cable negro de la lámpara al cable de línea eléctrica caliente con una tuerca de cable.
8
Coloque cuidadosamente todos los cables en la caja de junctura, coloque el dosel en los esparragos de montaje y seguro en su lugar con dos tuercas capuchon.
3
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077 800.323.3226 - 847.626.6300
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Marquer les emplacements des trous d'ancre sur la plaque de montage et ... Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un ...
1A. 3. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards ... Connecter le fil noir du luminaire (rond et
Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threaded pipe and secure it in place with the washer and hex nut ...
Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut. Place the decorative cup ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
Colorado Springs 6 Light Foyer. 1.1. F3046-6. Foyer. F3046/6. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product
G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandescent dimmer. This instru
Lennon 5 Light Semi-Flush Mount. 1.0. SF340. SF340. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Installation Instructions for. Hamlet 2 Light Semi-Flush Mount. 1.0. SF325. SF325. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
Colorado Springs 1 Light Pendant. 1.2. P1390. Pendant. P1390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant. NEC junction boxes. This product is safety listed for damp locations. This product may
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 4. 1. 1.
Placez la coupe sur le tuyau fileté et fixez-le en place en vissant le fleuron sur le tuyau fileté. 4. 5. AMPOULE. ATTENTION RISQUE INCENDIE. : D'. Ce produit ...
Conecte el cable blanco de la lámpara al cable de lÃnea de energÃa neutra con una tuerca para cable. Conecte el cable negro de la lámpara al cable de lÃnea ...
Secure the mounting plate to the junction box. ... Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the ...
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
á. Conecte el cable negro de la l mpara al cable de alimentación de línea caliente con un tapón de alambre. á. Alinee las ranuras en el base de la l mpara para ...
