Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut. Place the decorative cup ...
Ceiling GENERAL PRODUCT INFORMATION: CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations.
Use minimum 90°c supply conductors.
This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
1A 1
SOCKET ASSEMBLY LAMP
2 3
THREADED PIPE
RUBBER WASHER
4
SHADE
LARGE WASHER HEX NUT DECORATIVE CUP
5
FINIAL 1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
3
Screw the threaded pipe to the bottom of socket assembly.
4
Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut.
5
Place the decorative cup onto the threaded pipe and secure it in place using the finial.
1
1.1
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c. 1A 1
ENSEMBLE DE DOUILLE AMPOULE
2 3
TUYAU FILETÉ
RONDELLE DE GOMME
4
ABAT-JOUR
RONDELLE GRANDE ECROU HEX COUPE DÉCORATIVE
5
FLEURON 1
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et appareil sur une boîte de sortie de la maison.
2
Vissez le tuyau fileté au fond de l'ensemble de douille.
3
Visser les ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de le luminaire pour obtenir des informations de Max Puissance.
4
Placez la rondelle de gomme, l'abat-jour, et la grande rondelle sur le tuyau fileté (dans cet ordre), puis les fixer en place à l'aide d'un écrou hexagonal.
5
Placez la coupe décorative sur le tuyau fileté et fixer en place à l'aide du fleuron.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min. 1A 1
ASAMBLEA DE ENCHUFE BOMBILLA
2 3
TUBO ROSCADO
ARANDELA DE GOMA
4
PANTALLA
ARANDELA GRANDE TUERCA HEX COPA DECORATIVA
5
FINIAL 1
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de salida de la casa.
2
Atornillar el tubo roscado a la parte inferior del asamblea de enchufe.
3
Atornille las bombillas en los enchufes. Consulte la etiqueta del casquillo de la lámpara para obtener información Max Potencia.
4
Coloque la arandela de goma, la pantalla, y la arandela grande en el tubo roscado (en ese orden), luego fijarlos en su lugar con una tuerca hexagonal.
5
Coloque la copa decorativa sobre el tubo roscado y fijarlo en su lugar con el finial.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Connect the fixture to a suitable ground in accordance with local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut.
Marquer les emplacements des trous d'ancre sur la plaque de montage et ... Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un ...
1A. 3. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards ... Connecter le fil noir du luminaire (rond et
Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threaded pipe and secure it in place with the washer and hex nut ...
Lennon 5 Light Semi-Flush Mount. 1.0. SF340. SF340. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
Installation Instructions for. Hamlet 2 Light Semi-Flush Mount. 1.0. SF325. SF325. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
Placez la coupe sur le tuyau fileté et fixez-le en place en vissant le fleuron sur le tuyau fileté. 4. 5. AMPOULE. ATTENTION RISQUE INCENDIE. : D'. Ce produit ...
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 4. 1. 1.
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
the applicable installation code by a person familiar with the ... Use minimum 90°c supply conductors. 4. 1. 2. 3. 3. 4. CAP NUT. THREADED NIPPLE. 3 ...
Conecte el cable blanco de la lámpara al cable de lÃnea de energÃa neutra con una tuerca para cable. Conecte el cable negro de la lámpara al cable de lÃnea ...
Secure the mounting plate to the junction box. ... Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the ...
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations. This product may be dimmed ...
á. Conecte el cable negro de la l mpara al cable de alimentación de línea caliente con un tapón de alambre. á. Alinee las ranuras en el base de la l mpara para ...