Prarielands 3 Light Flush Mount - The Lighting Gallery
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations. This product may be dimmed ...
Ceiling GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for damp locations.
1A
4
3
MOUNTING PLATE
1 CAP NUT
FIXTURE BASE FIXTURE SCREW
5
8
5
NUT LAMP
7 INNER FRAME OUTER FRAME 1
Secure the mounting plate to the junction box.
2
Connect the fixture to a suitable ground in accordance to local electrical codes.
3
Connect the white fixture wire to the neutral power line wire with a wire nut.
4
Connect the black fixture wire to the hot power line wire with a wire nut.
5 1
Place the fixture base onto the mounting plate studs and secure them in place by tightening the cap nuts.
6
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
7
Install the glass panel by carefully placing them into the inner frame and securing them using the tabs.
8
Align the slots on the frame with the fixture screws, push the frame against the fixture base, and secure it in place by tightening the fixture screws into the nuts.
1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A
4
3
PLAQUE DE MONTAGE
1 ÉCROU CAPUCHON
BASE DE LUMINAIRE VIS DE LUMINAIRE
5
8
5
ÉCROU AMPOULE
7 CADRE INTÉRIEUR CADRE EXTÉRIEUR 1
Fixer la plaque de montage sur le boîte de jonction.
2
Connecter le luminaire à un terrain approprié conformément aux codes électriques locaux.
3
Connecter le fil blanc de luminaire pour le fil de ligne à neutre avec un écrou de fil.
4
Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
5 1
Placez la base de luminaire sur les goujons de montage de le luminaire et fixez-les en place en serrant les écrous capuchon.
6
Visser les ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de le luminaire pour obtenir des informations de Max Puissance.
7
Installez le panneau de verre en les plaçant soigneusement dans le cadre intérieur et les fixer à l'aide des languettes.
8
Alignez les fentes sur le cadre avec les vis de luminaire, poussez le cadre contre la base de luminaire et le fixer en place en serrant les vis de luminaire dans les écrous.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
4
3
PLACA DE MONTAJE
1 TUERCA CAPUCHON BASE DE LA LÁMPARA TORNILLO DE LA LÁMPARA
5
8
5
TUERCA BOMBILLA
7 MARCO INTERIOR MARCO EXTERIOR 1
Fije la placa de montaje a la caja eléctrica con dos tornillos de montaje.
2
Conecte la lámpara a una puesta a tierra adecuada de acuerdo a los códigos eléctricos locales.
3
Conecte el cable blanco de la lámpara al cable de la línea de alimentación neutra con una tuerca para cable.
4
Conecte el cable negro de la lámpara al cable de la línea eléctrica caliente con una tuerca para cable.
5 1
Coloque la base en los esparragos de montaje de la lámpara y fijarlo en su lugar apretando las tuercas capuchon.
6
Atornille las bombillas en los enchufes. Consulte la etiqueta del enchufe de la lámpara para obtener información Max de Potencia.
7
Instale el panel de vidrio colocando cuidadosamente en el marco interior y asegurarlos utilizando las lengüetas.
8
Alinee las ranuras en el marco con los tornillos de la lámpara, empuje la armadura contra la base de la lámpara, y seguro en su lugar apretando los tornillos de la lámpara en las tuercas.
the applicable installation code by a person familiar with the ... Use minimum 90°c supply conductors. 4. 1. 2. 3. 3. 4. CAP NUT. THREADED NIPPLE. 3 ...
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 4. 1. 1.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut. Place the decorative cup ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
Connect the black fixture wire to the hot power line wire with a wire nut. Align the keyed slots ... the hazards involved. Use minimum 90°c supply conductors. G. P.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
These fixtures are intended to be installed utilizing compliant junction. NEC boxes. This product is safety listed for damp locations. Incandescent lamps may be ...
Secure the mounting plate to the junction box. ... Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the ...
Connect the fixture to a suitable ground in accordance with local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut.
Placez la coupe sur le tuyau fileté et fixez-le en place en vissant le fleuron sur le tuyau fileté. 4. 5. AMPOULE. ATTENTION RISQUE INCENDIE. : D'. Ce produit ...
á. Conecte el cable negro de la l mpara al cable de alimentación de línea caliente con un tapón de alambre. á. Alinee las ranuras en el base de la l mpara para ...
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...
Marquer les emplacements des trous d'ancre sur la plaque de montage et ... Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un ...
1A. 3. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards ... Connecter le fil noir du luminaire (rond et