Install the glass panels by carefully sliding them into the housing and securing ... Connect the white fixture wire to the neutral power line wire with a wire nut.
Outdoor GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is safety listed for damp locations. This product may be dimmed with a low voltage electronic dimmer.
Use minimum 90°c supply conductors.
This instruction shows a typical installation.
1A
MOUNTING PLATE
MOUNTING PLATE SCREW MOUNTING PLATE STUD
GLASS PANEL
3
FIXTURE BASE
3
1 HOUSING
CLIP
MOUNTING PLATE NUT
7
7
1 8 2
8
BRACKET SCREW BRACKET
HOUSING SCREW
BOTTOM GLASS PANEL
HOUSING
1
Install the glass panels by carefully sliding them into the housing and securing them using the clips.
2
Install the bottom glass panel to the housing and secure it using the brackets and bracket screws.
3
Secure the mounting plate to the junction box with two mounting plate screws.
4
Connect the fixture to a suitable ground in accordance to local electrical codes.
5 1
Connect the white fixture wire to the neutral power line wire with a wire nut.
6
Connect the black fixture wire to the hot power line wire with a wire nut.
7
Place the fixture base onto the mounting plate studs and secure them in place using the mounting plate nuts.
8
Install the housing onto the fixture base and secure it in place using the housing screws.
1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A
PLAQUE DE MONTAGE
VIS DE MONTAGE PANNEAU DE VERRE
GOUJON DE MONTAGE
3
BASE DE LUMINAIRE
3
1 LOGEMENT
CLIP
ECROU DE MONTAGE
7
7
1 8 2
8
VIS DE SUPPORT SUPPORT
VIS DE LOGEMENT
PANNEAU DE VERRE INFERIEUR
LOGEMENT
1
Installer les panneaux de verre soigneusement faisant glisser dans le logement et les fixant à l'aide de clips.
2
Installer le panneau de verre inférieur au logement et sûr avec les supports et vis de support.
3
Fixer la plaque de montage sur le boîte de jonction avec deux vis de montage.
4
Connecter le luminaire à un terrain approprié conformément aux codes électriques locaux.
5 1
Connecter le fil blanc de luminaire pour le fil de ligne à neutre avec un écrou de fil.
6
Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
7
Placez la base de luminaire sur les goujons de montage de le luminaire et fixez-les en place en serrant les écrous de montage.
8
Installer le logement sur la base de luminaire et fixer en place à l'aide des vis de logement.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
PLACA DE MONTAJE
TORNILLO DE MONTAJE PANEL DE VIDRIO
ESPARRAGO DE MONTAJE
3
BASE DE LA LÁMPARA
3
1 VIVIENDA
CLIP
TUERCA DE MONTAJE
7
7
1
2
8
TORNILLO DEL SOPORTE
8
SOPORTE
TORNILLO DE LA VIVIENDA
PANEL DE VIDRIO DEL FONDO
VIVIENDA
1
Instale los paneles de vidrio cuidadosamente deslizándolas en la carcasa y asegurándolos con los clips.
2
Instale el panel de vidrio de fondo para la vivienda y seguro usando los soportes y tornillos del soporte.
3
Fije la placa de montaje a la caja eléctrica con dos tornillos de montaje.
4
Conecte la lámpara a una puesta a tierra adecuada de acuerdo a los códigos eléctricos locales.
5 1
Conecte el cable blanco de la lámpara al cable de la línea de alimentación neutra con una tuerca para cable.
6
Conecte el cable negro de la lámpara al cable de la línea eléctrica caliente con una tuerca para cable.
7
Coloque el base de la lámpara en los esparragos de montaje de la lámpara y fijarlo en su lugar apretando las tuercas de montaje.
8
Instalar la vivienda sobre la base de la lámpara y asegúrelo en su lugar utilizando los tornillos de la vivienda.
NEC junction boxes. This product is safety listed for damp locations. For a complete list of dimmers, visit out website at www.Feiss.com. CAUTION RISK OF FIRE.Termes manquants :
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
Secure the fixture to the post with the post screws making sure to neatly tuck in all wiring. ... Place the cover over the frame and secure it in place by screwing the finial onto the nipple ... Feiss reserves the right to ... A Generation Brands Com
F 455, F 457, F 458. M. M. M. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar ...
Connect the white driver wire to the neutral power line wire with a wire nut. ... Insert the glass panels into the housing and secure them using the glass panel ...
For a complete list of dimmers, visit out website at www.Feiss.com. This instruction shows a .... improvements without notification. A Generation Brands Company.
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Marquer les emplacements des trous d'ancre sur la plaque de montage et ... Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un ...
Cadence 2 Light Flush Mount. 1.1. FM390. Ceiling. FM390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC ...
Lennon 5 Light Semi-Flush Mount. 1.0. SF340. SF340. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Port Washington, NY 11050 ... Properly secure the safety cord to the bracket on mounting back plate to temporary hang the fixture in place (FM-38934 only).
Determine the height of the fixture with the provided stems and assemble them by screwing them together. Secure the mounting plate to the junction box.
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...