NEC junction boxes. This product is safety listed for damp locations. For a complete list of dimmers, visit out website at www.Feiss.com. CAUTION RISK OF FIRE.
Outdoor GENERAL PRODUCT INFORMATION: CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations.
Use minimum 90°c supply conductors.
For a complete list of dimmers, visit out website at www.Feiss.com
1A
JUNCTION BOX
4
3
HEX NUT
1
MOUNTING PLATE MOUNTING PLATE STUD
FIXTURE BASE CAP NUT
6
5
5
BRACKET SCREW
6
BRACKET OUTER GLASS PANEL THREADED PIPE
FIXTURE SCREW
7 7 FIXTURE
DIFFUSER
8 1
RUBBER WASHER
STEEL WASHER
HEX NUT
FINIAL
9 1
Secure the mounting plate to the junction box.
2
Connect the fixture to a suitable ground in accordance with local electrical codes.
3
Connect the white fixture wire to the neutral power line wire with a wire nut.
4
Connect the black fixture wire to the hot power line wire with a wire nut.
5
Place the fixture base onto the mounting plate studs and secure it with the two cap nuts.
6
Install the outer glass panels by inserting them into the fixture and securing them with the brackets and bracket screws.
7
Install the fixture to the fixture base by screwing the fixture screws into the hex nuts in the fixture base.
8
Place the diffuser, rubber washer, and steel washer onto the threaded pipe (in that order) and secure in place with the hex nut.
9
Screw the finial onto the threaded pipe.
1
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c.
1A
BOÎTE DE JONCTION
4
3
PLAQUE DE MONTAGE
ECROU HEX
1
GOUJON DE MONTAGE BASE DE LUMINAIRE ECROU CAPUCHON
6
5
5
VIS DE SUPPORT
6
SUPPORT PANNEAUX DE VERRE EXTÉRIEURE TUYAU FILETÉ
VIS DE LUMINAIRE
7 7 LUMINAIRE
DIFFUSEUR
8 1
RONDELLE DE GOMME
RONDELLE D’ACIER
ECROU HEX
FLEURON
9 1
Fixez la plaque de montage à la boîte de jonction.
2
Connectez le luminaire à un terrain approprié conformément avec les codes électriques locaux.
3
Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un écrou de fil.
4
Connectez le fil noir de luminaire au fil de la ligne d'alimentation chaude avec un écrou de fil.
5
Placez la base de luminaire sur les goujons de montage et le fixer avec les deux écrous capuchon.
6
Installez les panneaux de verre extérieures en les insérant dans le luminaire et les fixer avec les supports et les vis de support.
7
Installez le luminaire à la base de luminaire en vissant les vis de luminaire dans les écrous hexagonaux dans la base de luminaire.
8
Placez le diffuseur, la rondelle de gomme, et la rondelle d'acier sur le tuyau fileté (dans cet ordre) et le fixer en place avec l'écrou hexagonal.
9
Vissez le fleuron sur le tuyau fileté.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min.
1A
CAJA DE CONEXIONES
4
3
PLACA DE MONTAJE
TUERCA HEX
1
ESPARRAGO DE MONTAJE BASE DE LA LÁMPARA TUERCA CAPUCHON
6
5
5
TORNILLO DEL SOPORTE
6
SOPORTE PANELE DE VIDRIO EXTERIOR TUBO ROSCADO
TORNILLO DE LA LÁMPARA
7 7 LÁMPARA
DIFUSOR
8 1
ARANDELA DE GOMA
ARANDELA DE ACERO
TUERCA HEX
FINIAL
9 1
Fije la placa de montaje a la caja de conexiones.
2
Conecte la lámpara a una tierra adecuada, de acuerdo con los códigos eléctricos locales.
3
Conecte el cable blanco de la lámpara al cable de línea de energía neutra con una tuerca para cable.
4
Conecte el cable negro de la lámpara al cable de línea eléctrica caliente con una tuerca para cable.
5
Coloque la base de la lámpara en los esparragos de montaje y fijarlo con las dos tuercas capuchon.
6
Instale los paneles de vidrio exteriores insertándolos en la lámpara y asegurándolos con los soportes y tornillos del soporte.
7
Instale la lámpara a la base de la lámpara atornillando los tornillos de la lámpara en las tuercas hexagonales en la base de la lámpara.
8
Coloque el difusor, la arandela de goma y arandela de acero sobre el tubo roscado (en ese orden) y seguro en su lugar con la tuerca hexagonal.
9
Atornille la finial firmemente en el tubo roscado.
Install the glass panels by carefully sliding them into the housing and securing ... Connect the white fixture wire to the neutral power line wire with a wire nut.
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
F 455, F 457, F 458. M. M. M. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar ...
Connect the white driver wire to the neutral power line wire with a wire nut. ... Insert the glass panels into the housing and secure them using the glass panel ...
For a complete list of dimmers, visit out website at www.Feiss.com. This instruction shows a .... improvements without notification. A Generation Brands Company.
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Marquer les emplacements des trous d'ancre sur la plaque de montage et ... Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un ...
Cadence 2 Light Flush Mount. 1.1. FM390. Ceiling. FM390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC ...
Lennon 5 Light Semi-Flush Mount. 1.0. SF340. SF340. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Port Washington, NY 11050 ... Properly secure the safety cord to the bracket on mounting back plate to temporary hang the fixture in place (FM-38934 only).
Determine the height of the fixture with the provided stems and assemble them by screwing them together. Secure the mounting plate to the junction box.
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
fixture's ground wire directly to the back plate using the green screw provided. ... PC Diffuser. Mounting Plate. Junction Box. Glass. (RPL-GLA-13114). Shade.
Conecte el cable blanco de la lámpara al cable de lÃnea de energÃa neutra con una tuerca para cable. Conecte el cable negro de la lámpara al cable de lÃnea ...