Wall GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for wet locations.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Use minimum 90°c supply conductors.
For a complete list of dimmers, visit out website at www.Feiss.com
1A
COVER
CLIP
2
10
OUTER GLASS PANEL
MOUNTING PLATE THUMB SCREW JUNCTION BOX
WHITE WIRE
4
4
NEUTRAL WIRE 9 1
COVER SCREW
7
5
FIXTURE
CAP NUT (Model OL12802 Only) 1
8 9
HOT WIRE
DIFFUSER
BLACK WIRE
FIXTURE SCREW
1
Secure the mounting plate to the junction box.
2
Install the outer glass panels by sliding them into the fixture from the top and secure them in place with the clips.
3
For Model OL12802 Only: Screw the cap nut onto the fixture backplate.
4
Install the diffuser by sliding it into the fixture from the bottom and secure with thumb screws.
5
Place the cover onto the fixture and secure it using the cover screws.
6
Connect the fixture to a suitable ground in accordance with local electrical codes.
7
Connect the white wire to the neutral power line wire with a wire nut.
8
Connect the black wire to the hot power line wire with a wire nut.
9
Neatly place the wires and wire nut connections into the junction box, mount the fixture base onto the mounting plate, and secure it with the fixtures screws.
10
For wet locations, caulk around the base of the fixture with waterproof construction sealant. 1
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c. 1A
COUVERCLE
AGRAFE
2
10
PANNEAU DE VERRE EXTÉRIEURE PLAQUE DE MONTAGE BOÎTE DE JONCTION
VIS DE POUCE FIL BLANC
4
4
FIL NEUTRE 9 1
VIS DE COUVERCLE
7
5 LUMINAIRE CAP NUT (Model OL12802 Only)
1
8
DIFFUSEUR
9 FIL CHAUDE
FIL NOIR VIS DE LUMINAIRE
1
Fixez la plaque de montage à la boîte de jonction.
2
Installez les panneaux de verre extérieures en les faisant glisser dans la fixation par le haut et fixez en place avec l’afrafes.
3
Pour Modèle OL12802 Seulement: visser l’écrou capuchon sur la plaque arrière du luminaire.
4
Installez le diffuseur en les faisant glisser dans le montage à partir du bas et les fixer avec les vis de pouce.
5
Placez le couvercle sur le luminaire et le fixer avec les vis de couvercle.
6
Connectez le luminaire à un terrain approprié conformément avec les codes électriques locaux.
7
Connectez le fil blanc au fil de la ligne d'alimentation neutre avec un écrou de fil.
8
Connectez le fil noir au fil de la ligne d'alimentation chaude avec un écrou de fil.
9
Soigneusement placer les câbles et connexions de noix de fil dans la boîte de jonction, monter la base de luminaire sur la plaque de montage, et le fixer avec les vis de luminaire.
10
Pour les endroits humides, calfeutrez autour de la base de luminaire avec une construction étanche étanchéité.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min. 1A
CUBIERTA
BROCHE
2
10
PANELE DE VIDRIO EXTERIOR PLACA DE MONTAJE CAJA DE JUNCTURA
TORNILLO DE PULGAR CABLE BLANCO
4
4
CABLE NEUTRO 9 1
TORNILLO DE LA CUBIERTA
7
5 LÁMPARA CAP NUT (Model OL12802 Only)
1
8
DIFUSOR
9 CABLE CALIENTE
CABLE NEGRO TORNILLO DE LA LÁMPARA
1
Fije la placa de montaje a la caja de conexiones.
2
Instale los paneles de vidrio exteriores por deslizándolos en la fijación de la parte superior y fijarlos en su lugar con los broches.
3
Para Modelo OL12802 Solamente: Atornille la tuerca de capuchon en la placa posterior de la lámpara.
4
Instale el difusor por deslizándolo en la fijación de la parte inferior y asegurarlo con los tornillos de pulgar.
5
Coloque la cubierta en la lámpara y fijarlo con los tornillos de la cubierta.
6
Conecte la lámpara a una tierra adecuada, de acuerdo con los códigos eléctricos locales.
7
Conecte el cable blanco al cable de línea de energía neutra con una tuerca para cable.
8
Conecte el cable negro al cable de línea eléctrica caliente con una tuerca para cable.
9
Coloque cuidadosamente los cables y conexiones de tuerca cable en la caja de conexiones, monte la base de la lámpara sobre la placa de montaje, y fijarlo con los tornillos de la lámpara.
10
Para lugares húmedos, calafatear alrededor de la base de la lámpara con sellador de construcción resistente al agua.
NEC junction boxes. This product is safety listed for damp locations. For a complete list of dimmers, visit out website at www.Feiss.com. CAUTION RISK OF FIRE.Termes manquants :
Do not block any ventilation openings. Install in accordance with the ... Contact your local government for disposal or recycling practices in your area.
Secure the fixture to the post with the post screws making sure to neatly tuck in all wiring. ... Place the cover over the frame and secure it in place by screwing the finial onto the nipple ... Feiss reserves the right to ... A Generation Brands Com
Insert the diffuser into the diffuser base, place the LED assembly on top of the diffuser, and secure it to the top of the housing ... A Generation Brands Company.
Install all glass panels by carefully sliding them into the fixture and securing them using the clips. Place the shade and spacer over the socket and secure them in ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 2. CAP N
44 Harbor Park Drive • Port Washington, NY 11050 ... Place the fixture over the mounting back plate and secure with mounting screws (B) and rubber gaskets ...
Connect the white driver wire to the neutral power line wire with a wire nut. ... Insert the glass panels into the housing and secure them using the glass panel ...
For a complete list of dimmers, visit out website at www.Feiss.com. This instruction shows a .... improvements without notification. A Generation Brands Company.
No warranty is provided for batteries and lightbulbs. This is your exclusive warranty. This warranty is valid for the original retail purchaser from the date of initial ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax (516) 515.5050. Western Distribution Center. 1750 Archibald Ave • Ontario, CA ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
the circuit breaker switch(es) that control the power to the fixture or room that you are ... CAUTION When handling the fixture, do not apply pressure to the LEDs.
Determine the height of the fixture with the provided stems and assemble them by screwing them together. Secure the mounting plate to the junction box.
Place the shade inside the decorative frame and install the brackets to the decorative frame using the bracket screws. Place the decorative frame over the threaded pipe and socket assembly and secure them together using the finial. Follow enclosed su
Install the glass panels by carefully sliding them into the housing and securing ... Connect the white fixture wire to the neutral power line wire with a wire nut.