Wall GENERAL PRODUCT INFORMATION: CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for wet locations.
Use minimum 90°c supply conductors.
This instruction shows a typical installation.
1A 5
COVER
10
CAP NUT FIXTURE SCREW
4
4 BRACKET
MOUNTING PLATE JUNCTION BOX
WHITE WIRE LAMP
NEUTRAL WIRE
1
3
9 5
7
2
CANDLE FOLLOWER
GLASS PANEL 1 HOT WIRE
8 BLACK WIRE
9
CANDLE TUBE
1
Secure the mounting plate to the junction box.
2
Install the candle follower by placing it on top of the candle tube. Repeat for remaining candle followers.
3
Screw the lamp(s) into the socket(s). Refer to the label on the lamp socket for Max Wattage information.
4
Install the glass panels by sliding them into the fixture and secure them using the brackets and cap nuts.
5
Place the cover onto the fixture and secure it using the cover screws.
6
Connect the fixture to a suitable ground in accordance with local electrical codes.
7
Connect the white fixture wire to the neutral power line wire with a wire nut.
8
Connect the black fixture wire to the hot power line wire with a wire nut.
9
Neatly place the wires and wire nut connections into the junction box, mount the fixture base onto the mounting plate, and secure it with the fixtures screws.
10
For wet locations, caulk around the base of the fixture with waterproof construction sealant. 1
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c. 1A 5
COUVERCLE
10
ECROU CAPUCHON VIS DE LUMINAIRE
4
4 SUPPORT
PLAQUE DE MONTAGE BOÎTE DE JONCTION
FIL BLANC AMPOULE
FIL NEUTRE
1
3
9 5
7
2
SUIVEUR DE BOUGIE
PANNEAU DE VERRE 1 FIL CHAUDE
8 FIL NOIR
TUBE BOUGIE
9
1
Fixez la plaque de montage à la boîte de jonction.
2
Installez les panneaux de verre en les faisant glisser dans le montage et fixez-les à l'aide des supports et des écrous capuchon.
3
Installez le suiveur de bougie en le plaçant sur le dessus de tube de bougie. Répétez pour le reste adeptes bougie.
4
Visser l’ampoule (s) dans la/les douille (s). Reportez-vous à l'étiquette sur la douille de lampe pour obtenir des informations Max Puissance.
5
Placez le couvercle sur le luminaire et le fixer avec les vis capuchon.
6
Connectez le luminaire à un terrain approprié conformément avec les codes électriques locaux.
7
Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un écrou de fil.
8
Connectez le fil noir de luminaire au fil de la ligne d'alimentation chaude avec un écrou de fil.
9
Soigneusement placer les câbles et connexions de noix de fil dans la boîte de jonction, monter la base de luminaire sur la plaque de montage, et le fixer avec les vis de luminaire.
10
Pour les endroits humides, calfeutrez autour de la base de luminaire avec une construction étanche étanchéité.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min. 1A 5
CUBIERTA
10
TUERCA CAPUCHON TORNILLO DE LA LÁMPARA
4
4 SOPORTE
PLACA DE MONTAJE CAJA DE CONEXIONES
CABLE BLANCO BOMBILLA
CABLE NEUTRO
3
9 5
7
1
2
SEGUIDOR DE VELA
PANELE DE VIDRIO 1
8
CABLE CALIENTE
CABLE NEGRO
TUBO DE VELA
9
1
Fije la placa de montaje a la caja de conexiones.
2
Instale los paneles de vidrio deslizándolos en la lámpara y asegurarlos utilizando los soportes y tuercas capuchon.
3
Instale el seguidor de vela colocándolo en la parte superior del tubo de vela. Repita para el resto de los seguidores de vela.
4
Atornille la/los bombilla(s) en la/los enchufe(s). Consulte la etiqueta en el casquillo de la lámpara para obtener información Max Potencia.
5
Coloque la cubierta en la lámpara y fijarlo con los tornillos de la cubierta.
6
Conecte la lámpara a una tierra adecuada, de acuerdo con los códigos eléctricos locales.
7
Conecte el cable blanco de la lámpara al cable de línea de energía neutra con una tuerca para cable.
8
Conecte el cable negro de la lámpara al cable de línea eléctrica caliente con una tuerca para cable.
9
Coloque cuidadosamente los cables y conexiones de tuerca cable en la caja de conexiones, monte la base de la lámpara sobre la placa de montaje, y fijarlo con los tornillos de la lámpara.
10
Para lugares húmedos, calafatear alrededor de la base de la lámpara con sellador de construcción resistente al agua.
Connect the black fixture wire to the hot power line wire with a wire nut. ... Refer to the label on the lamp socket for Max Wattage information. Install the glass ...
Do not block any ventilation openings. Install in accordance with the ... Contact your local government for disposal or recycling practices in your area.
Screw the lamp into the socket. Refer to the label on the socket for Max Wattage information. Place the cover onto the frame nipple and secure it in place by screwing the cap onto the nipple. 6. CAUTION RISK OF FIRE. -. This product must be installed
Refer to the label on the socket for Max Wattage information. Follow enclosed supplement installation ... without notification. A Generation Brands Company.
Connect the white driver wire to the neutral power line wire with a wire nut. ... Insert the glass panels into the housing and secure them using the glass panel ...
For a complete list of dimmers, visit out website at www.Feiss.com. This instruction shows a .... improvements without notification. A Generation Brands Company.
Install all glass panels by carefully sliding them into the fixture and securing them using the clips. Place the shade and spacer over the socket and secure them in ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 2. CAP N
Secure the fixture to the post with the post screws making sure to neatly tuck in all wiring. Insert the shade into the frame and place it over the socket. Screw the lamp into the socket. Refer to the label on the socket for Max Wattage information.
Determine the height of the fixture with the provided stems and assemble them by screwing them together. Secure the mounting plate to the junction box.
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 2. POST. POST SCREW. 3. 4. 4. GL
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Place the shade and spacer over the socket and secure them in place by screwing the collar nut onto the socket. Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. Install the cover to the fixture arm an