Outdoor GENERAL PRODUCT INFORMATION: This product is listed by one of the following “Nationally Recognized Testing Laboratory”
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is suitable for damp locations. This product may be dimmed with a low voltage electronic dimmer.
Use minimum 90°c supply conductors. This instruction shows a typical installation.
1A
CLIP
4
1 GLASS PANEL FIXTURE LOOP
3
KNURLED NUT
WASHER COVER
1
NIPPLE
FRAME
2 FRAME SCREW
HOUSING
HOUSING
1
Install all glass panels by carefully sliding them into the housing and securing them using the clips.
2
Secure the frame to the housing using the frame screws.
3
Place the cover and washer onto the nipple and secure them in place by screwing the knurled nut onto the nipple, then screw the fixture loop onto the nipple.
4
Follow enclosed supplement installation instructions for electrical and fixture installation onto house junction box.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
CLIP
4
1 BOUCLE DE LUMINAIRE
PANNEAU DE VERRE
3
ÉCROU MOLETÉ
RONDELLE COUVERCLE
1
ATTACHE
CADRE
2 VIS DE CADRE
LOGEMENT
LOGEMENT
1
Installer tous les panneaux de verre en les faisant glisser avec précaution dans le logement et les fixer à l'aide des clips.
2
Fixer le cadre au logement à l'aide des vis de cadre.
3
Placez le couvercle et la rondelle sur le attache et les fixer en vissant l'écrou moleté sur l’attache, puis vissez la boucle de luminaire sur l’attache.
4
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et luminaire sur une boîte de jonction de la maison.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
CLIP
4
1 BUCLE DE LA LAMPARA
PANELE DE VIDRIO
3
TUERCA MOLETEADA
RONDELLE CUBIERTA
1
CONECTADOR
MARCO
2 TORNILLO DEL MARCO
VIVIENDA
VIVIENDA
1
Instale todos los paneles de vidrio deslizándolos con cuidado en la vivienda y asegurándolos con los clips.
2
Fije el marco a la vivienda con los tornillos del marco.
3
Coloque la cubierta y la arandela en el conectador y fijarlos en su lugar atornillando la tuerca moleteada en el conectador, luego atornillar el bucle de la lampara en el conectador.
4
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de junctura de la casa.
Secure the fixture to the post with the post screws making sure to neatly tuck in all wiring. ... Place the cover over the frame and secure it in place by screwing the finial onto the nipple ... Feiss reserves the right to ... A Generation Brands Com
Install all glass panels by carefully sliding them into the fixture and securing them using the clips. Place the shade and spacer over the socket and secure them in ...
Install the glass panels by carefully sliding them into the housing and securing ... Connect the white fixture wire to the neutral power line wire with a wire nut.
Place the shade inside the decorative frame and install the brackets to the decorative frame using the bracket screws. Place the decorative frame over the threaded pipe and socket assembly and secure them together using the finial. Follow enclosed su
Do not block any ventilation openings. Install in accordance with the ... Contact your local government for disposal or recycling practices in your area.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house junction box. Raise the housing up to the fixture so that the ...
Augmenter le logement jusqu'Ã le luminaire de sorte que le attache sort par le haut de le luminaire et les fixer ensemble en vissant le fleuron sur le attache.
Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut.
Insert the diffuser into the diffuser base, place the LED assembly on top of the diffuser, and secure it to the top of the housing ... A Generation Brands Company.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 2. CAP N
44 Harbor Park Drive • Port Washington, NY 11050 ... Place the fixture over the mounting back plate and secure with mounting screws (B) and rubber gaskets ...
Connect the white driver wire to the neutral power line wire with a wire nut. ... Insert the glass panels into the housing and secure them using the glass panel ...
For a complete list of dimmers, visit out website at www.Feiss.com. This instruction shows a .... improvements without notification. A Generation Brands Company.
No warranty is provided for batteries and lightbulbs. This is your exclusive warranty. This warranty is valid for the original retail purchaser from the date of initial ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax (516) 515.5050. Western Distribution Center. 1750 Archibald Ave • Ontario, CA ...