Refer to the label on the socket for Max Wattage information. Follow enclosed supplement installation ... without notification. A Generation Brands Company.
Outdoor GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes. Incandescent lamps may be dimmed with a standard incandescent dimmer. LED lamps may be dimmed with a LED dimmer. Consult lamp manufacturer for additional information.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for wet locations.
1A
2
FIXTURE
1
LAMP
3
1
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage information.
2
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
3
For wet locations, caulk around the base of the fixture with waterproof construction sealant.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
3 LUMINAIRE
1
AMPOULE
3
1
Vissez les ampoules dans les douilles. Reportez-vous à l'étiquette sur la prise pour les informations Max Wattage.
2
Suivez les instructions d'installation complétées pour l'installation électrique et de montage sur la boîte de sortie de la maison.
3
Pour les endroits humides, calfeutrer autour de la base de l'appareil avec un joint d'étanchéité étanche à l'eau.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
2 LÂMPARA
1
BOMBILLA
3
1
Atornille las bombillas en los enchufes. Consulte la etiqueta en el enchufe para obtener información sobre el Vatiaje máximo.
2
Siga las instrucciones adjuntas de instalación del suplemento para la instalación eléctrica y de accesorios en la caja de salida de la casa.
3
Para lugares húmedos, calafatear alrededor de la base del aparato con sellador de construcción impermeable.
Connect the white driver wire to the neutral power line wire with a wire nut. ... Insert the glass panels into the housing and secure them using the glass panel ...
Place the shade and spacer over the socket and secure them in place by screwing the collar nut onto the socket. Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. Install the cover to the fixture arm an
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground in accordance to local ...
Screw the lamp into the socket. Refer to the label on the socket for Max Wattage information. Place the cover onto the frame nipple and secure it in place by screwing the cap onto the nipple. 6. CAUTION RISK OF FIRE. -. This product must be installed
Mark the anchor hole locations on the mounting plate and remove the mounting plate. ... Connect the black fixture wire to the hot power line wire with a wire nut.
Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture ... For a complete list of dimmers, visit out website at www.Feiss.com.
Connecter le fil blanc du luminaire (carré et / ou rigide) pour le fil de ligne à neutre ... Parfaitement placer tous les fils dans la boîte électrique, le montage d'essai ...
sujeción en caja de salida de casa. Instale la lámpara enroscándolo en la toma de corriente. Consulte la etiqueta del casquillo de la lámpara para obtener.
Install and secure the string of beads by hooking them to the top and bottom of the fixture. Install the candle tube by slipping through the socket. Install candle ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamps into the sockets. Refer to the ...
For a complete list of dimmers, visit out website at www.Feiss.com. This instruction shows a .... improvements without notification. A Generation Brands Company.
CABLE NEGRO. CAJA ELÉCTRICA. PLACA DE. MONTAJE. LÁMPARA. PRECAUCIÓN: RIESGO DE INCENDIO. Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los
Augmenter le logement jusqu'Ã le luminaire de sorte que le attache sort par le haut de le luminaire et les fixer ensemble en vissant le fleuron sur le attache.