Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture ... For a complete list of dimmers, visit out website at www.Feiss.com.
Outdoor GENERAL PRODUCT INFORMATION: CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for wet locations. For a complete list of dimmers, visit out website at www.Feiss.com
Use minimum 90°c supply conductors.
1A
COVER
JUNCTION BOX
SCREW AND WASHER
LED ASSEMBLY SCREW
1 LED ASSEMBLY
BRACKET
2 GLASS PANEL
3 ANCHOR MOUNTING PLATE
COVER SCREW
ANCHOR SCREW
12 13
FIXTURE SCREW
FIXTURE
1
Insert the glass panels into the shade, then secure them by installing the brackets using the screws and washers.
2 3
Install the LED assembly to the top fixture using the LED assembly screws.
4
Temporarily install the mounting plate to the junction box.
5 6
Mark the anchor hole locations on the mounting plate and remove the mounting plate.
7
Secure the mounting plate to the junction box.
8
Screw the anchor screws into the anchors.
Install the cover to the top of the fixture using the cover screws.
Drill appropriate size holes at the marked locations and install the anchors.
9 10
Connect the fixture to a suitable ground in accordance with local electrical codes.
11
Connect the black fixture wire to the hot power line wire with a wire nut.
12
Mount the fixture base onto the mounting plate and secure it with the fixture screws.
13
For wet locations, caulk around the base of the fixture with waterproof construction sealant.
Connect the white fixture wire to the neutral power line wire with a wire nut.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
COUVERCLE
BOÎTE DE JONCTION
VIS ET RONDELLE
VIS DE ENSEMBLE LED
1 ENSEMBLE LED
SUPPORT
2 PANNEAU DE VERRE
3 ACRE PLAQUE DE MONTAGE VIS DE ACRE
VIS DE COUVERCLE
12 13
VIS DE LUMINAIRE
LUMINAIRE
1
Insérez les panneaux de verre dans l'abat-jour, puis fixez-les en installant les supports à l'aide des vis et des rondelles.
2
Installez l'ensemble LED sur le montage supérieur à l'aide des vis d'assemblage LED.
3
Installez le couvercle sur le dessus de luminaire à l'aide des vis de couvercle.
4
Installer temporairement la plaque de montage à la boîte de jonction.
5
Marquer les emplacements des trous d'ancre sur la plaque de montage et enlever la plaque de montage.
6
Percer des trous de la taille appropriée aux emplacements marqués et installez les ancres.
7
Fixez la plaque de montage à la boîte de jonction.
8
Visser les vis d'ancres dans l’ancres.
9
Connectez le luminaire à un terrain approprié conformément aux codes électriques locaux.
10
Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un écrou de fil.
11
Connectez le fil noir de luminaire au fil de la ligne d'alimentation chaude avec un écrou de fil.
12
Montez la base de luminaire sur la plaque de montage et le fixer avec les vis de luminaire.
13
Pour les endroits humides, calfeutrez autour de la base de le luminaire avec une construction étanche étanché
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
COVER
CAJA DE JUNCTURA
TORNILLO Y ARANDELA
LED ASSEMBLY SCREW
1 LED ASSEMBLY
SOPORTE
2 PANELE DE VIDRIO
3 ANCLAJE PLACA DE MONTAJE
TORNILLO DE LA CUBIERTA
TORNILLO DEL ANCLAJE
12 13
TORNILLO DE LÁMPARA
LÁMPARA
1
Inserte los paneles de vidrio en la pantalla, y luego asegurarlos instalando los soportes utilizando los tornillos y las arandelas.
2
Instale el ensamblaje LED en la parte superior de la lámpara usando los tornillos del esamblaje LED.
3
Instale la cubierta en la parte superior de la lámpara usando los tornillos de la cubierta.
4
Instalar temporalmente la placa de montaje a la caja de juntura.
5
Marque las ubicaciones de los orificios de anclaje en la placa de montaje y retire la placa de montaje.
6
Taladro agujeros de tamaño apropiado en los lugares marcados y instalar los anclajes.
7
Fije la placa de montaje a la caja de junctura.
8
Atornille los tornillos de anclaje en los anclajes.
9
Conecte la lámpara a una tierra adecuada, de acuerdo con los códigos eléctricos locales.
10
Conecte el cable blanco de la lámpara al cable de línea de energía neutra con una tuerca para cable.
11
Conecte el cable negro de la lámpara al cable de línea eléctrica caliente con una tuerca para cable.
12
Monte la base de lámpara sobre la placa de montaje y fijarlo con los tornillos de lámpara.
13
Para lugares húmedos, calafatear alrededor de la base de la lámpara con sellador de construcción resistente al agua.
Augmenter le logement jusqu'Ã le luminaire de sorte que le attache sort par le haut de le luminaire et les fixer ensemble en vissant le fleuron sur le attache.
... with this product by Modern Forms could result in personal injury or property damage, ... Secure the mounting back plate to the junction box using the screws ...
Refer to the label on the socket for Max Wattage information. Follow enclosed supplement installation ... without notification. A Generation Brands Company.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house junction box. Raise the housing up to the fixture so that the ...
Connect the white driver wire to the neutral power line wire with a wire nut. ... Insert the glass panels into the housing and secure them using the glass panel ...
44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs, GA 30122. Western Distribution Center.
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
Fije la parte superior del brazo a la cubierta de la lámpara colocando una arandela ... coloque el capuchon decorativo empujándola en el brazo completamente.
This product is listed by one of the following. â ationally ecognized esting aboratoryâ. N. R. T. L ... SUIVEUR DE BOUGIE. PANNEAU. DE VERRE. LOGEMENT. 2.
Place the shade and spacer over the socket and secure them in place by screwing the collar nut onto the socket. Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. Install the cover to the fixture arm an
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Secure the mounting plate to the junction box with two mounting plate screws. Screw the ... Mount the fixture base onto the mounting plate and secure it with the fixture screws. .... Feiss reserves the right to ... A Generation Brands Company.
Install the candle follower by placing it on top of the socket. Screw the lamp into the socket. Refer to the label on the socket for Max Wattage information. Repeat ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 2. CAP N
Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground in accordance to local ...
compliant junction. NEC boxes. This product is safety listed for wet locations. Incandescent lamps may be dimmed with a standard incandescent dimmer. LED.
Rule engine design. State machine over a precursing REST architecture. ... as well as to stream datas passed from java to Catia C++ processes. Use of RxJava.