INSTALLATION INSTRUCTIONS 911-Outdoor Wall Sconce WS-W14911/WS-W14911F CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE BEGINNING. Read all instructions before installing. System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations. When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only. Retain installation instructions for future maintenance reference. WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing. MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth. MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer. Lisez toutes les instructions avant l’installation. Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux règlements locaux. Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base. ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées. NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un chiffon humide.
Shut off the power at the circuit breaker and remove existing fixture, including the crossbar. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2) 3. 4. 5.
Remove the mounting screw (B) and silicone gasket (C) from the fixture. Secure the mounting back plate to the junction box using the screws provided with the junction box. NOTE: The side of the mounting back plate marked “GND” must face out. Connect the fixture’s input wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secure. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE/ CONNECTING THE WIRE 6. 7.
Secure the canopy to the mounting plate using the mounting screw (B) and the silicone gasket (C). To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the outside of fixture back plate where it meets the wall. Leave a space at a bottom to allow moisture to escape Fig.3.
Do not try to light any appliance. • Do not touch any ..... action of LP Gas must be used on all pipe connec- tions. ... tube, which sets on the orifice of the valve, and.
This oven is not designed for commercial use. • Do not climb anywhere on the oven. • Do not leave children alone near the oven or let them play with the controls ...
El primer paso para su instalación debe de ser el de medir las dimensiones de la apertura y compararlas con las que se indican en el cuadro de dimensiones del hueco de la figura 1. Posiblemente encontrará que algún trabajo de carpinterÃa será ne
... with this product by Modern Forms could result in personal injury or property damage, ... Secure the mounting back plate to the junction box using the screws ...
You may find little or no cabinet work being necessary. United States and Canada. PRODUCT ..... element in the oven should become red. Convection (some ...
Allow at least 27¼" (69,2 cm) clearance in front of oven for door depth when it is open. 3. Dimension G ..... IMPORTANT. Do not lift the oven by the door handle.
In cold weather shipping and storage conditions, make sure that oven is in ... aluminum house wiring, use only connectors that are approved for joining copper ...
a convection baking or roasting, both elements cycle on and off alternately and the convection fan will run. The convection fan will stop running when the oven.
44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs, GA 30122. Western Distribution Center.
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any ...... Si l'ouverture est trop large pour fixer solidement l'appareil à ...
Your new wall oven has been designed to fit a limited variety of cutout sizes to make the job of installing ..... The convection fan will stop running when the oven.
interest to children in the cabinets above the appliance. ... children from touching the oven door or glass ..... sufrir quemaduras o lesiones graves si se suben al.
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
sin la ventilación adecuada puede ser peligroso. La corriente ... y de atrás hacia adelante. 2. Ajuste de .... el horno sin la guarda de seguridad instalada. No usar.
adjuster. 22 1/2". Hole for. Cord. • If width opening is too wide to secure unit to cabinet with mounting screws, add plywood filler strips. • If height opening is at ...
junction box should be located as shown in Figure. 1 or Figure 2 and .... numbers and a lot number or letter from the serial plate on your oven. ... For typical under counter installation of an electric built-in oven see Figure below. Note 1: 4â x
sible for service required to correct a faulty installation. ... vice technician must perform all other service. ... These items can melt or burn during self-cleaning.
The installer must show the customer the location of the circuit breaker panel or fuse box so that they know where and how to turn off power to the oven. Dacor is ...
Port Washington, NY 11050. Central Distribution Center ... Place the fixture over the mounting plate and secure it with mounting screws (B). NOTE: DIMMING ...
El primer paso para su instalación debe de ser el de medir las dimensiones de la apertura y compararlas con las que se indican en el cuadro de dimensiones del hueco de la figura 1. Posiblemente encontrará que algún trabajo de carpinterÃa será ne
Drill holes on the wall aligned with the keyhole location on the cover plate. 4. Insert plastic anchors (C) into the holes. Insert wood screws (A) into the plastic ...
