Wall GENERAL PRODUCT INFORMATION: CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations.
Use minimum 90°c supply conductors. 1A
4
1
LAMP
3
CANDLE FOLLOWER
2
CANDLE TUBE
SOCKET
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Install the candle tubes by slipping them over the sockets.
3
Install the candle followers by placing them on top of the candle tubes.
4
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage information.
1
1.0
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c. 1A
4
1
AMPOULE
3
SUIVEUR DE BOUGIE
2
TUBE BOUGIE
DOUILLE
1
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et appareil sur une boîte de sortie de la maison.
2
Installez les tubes de bougies en les glissant sur les sockets.
3
Installez les adeptes bougie en les plaçant sur le dessus des tubes de bougies.
4
Visser les lampes dans les douilles. Reportez-vous à l'étiquette sur la prise d'informations Max Puissance.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min.
1A
4
1
BOMBILLA
3
SEGUIDOR DE VELA
2
TUBO DE VELA
ENCHUFE
1
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de salida de casa.
2
Instale los tubos vela por el deslizamiento de ellos en los zócalos.
3
Instalar los seguidores de la vela por su inclusión en la parte superior de los tubos de la vela.
4
Atornille las bombillas en los enchufes. Consulte la etiqueta en la toma de información Max Potencia.
Install and secure the string of beads by hooking them to the top and bottom of the fixture. Install the candle tube by slipping through the socket. Install candle ...
Connecter le fil blanc du luminaire (carré et / ou rigide) pour le fil de ligne à neutre ... Parfaitement placer tous les fils dans la boîte électrique, le montage d'essai ...
sujeción en caja de salida de casa. Instale la lámpara enroscándolo en la toma de corriente. Consulte la etiqueta del casquillo de la lámpara para obtener.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamps into the sockets. Refer to the ...
CABLE NEGRO. CAJA ELÉCTRICA. PLACA DE. MONTAJE. LÁMPARA. PRECAUCIÓN: RIESGO DE INCENDIO. Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los
Place the shade and spacer over the socket and secure them in place by screwing the collar nut onto the socket. Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. Install the cover to the fixture arm an
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors.
Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground in accordance to local ...
Connect the white fixture wire to the neutral power line wire with a wire nut. Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws. Install th
Mark the anchor hole locations on the mounting plate and remove the mounting ... Connect the black fixture wire (round and/or smooth) to the hot power line wire ...
Connect the white fixture wire (square and/or rigid) to the neutral power line wire ... G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
Mark the anchor hole locations on the mounting plate and remove the mounting plate. ... Connect the black fixture wire to the hot power line wire with a wire nut.
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...