CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors.
Wall GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
Use minimum 90°c supply conductors.
1A SHADE
8
NEUTRAL WIRE
LAMP
WHITE WIRE
7 CANDLE TUBE
ELECTRICAL BOX 1
6
1 MOUNTING PLATE MOUNTING PLATE SCREW
FIXTURE 5
HOT WIRE BLACK WIRE
SET SCREW
1
Secure the mounting plate to the electrical box with the two provided mounting plate screws.
2
Connect the fixture ground wire to a suitable ground in accordance to local electrical codes.
3
Connect the white fixture wire to the neutral power line wire with a wire nut.
4
Connect the black fixture wire to the hot power line wire with a wire nut.
5
Mount the fixture base onto the mounting plate and secure it with the set screws.
6
Install candle tube by slipping through socket.
7
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
8
Install shade by snapping onto bulb.
1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A OMBRE
8
FIL NEUTRE
AMPOULE FIL BLANC
7 TUBE BOUGIE
COFFRET ÉLECTRIQUE 1
6
1 MONTAGE PLAQUE MONTAGE VIS PLAQUE
LUMINAIRE 5
FIL CHAUD FIL NOIR
VIS DE FIXATION
1
Fixez la plaque de montage à la boîte électrique avec les deux vis fournies plaque de montage.
2
Connectez le fil de terre du luminaire pour une masse appropriée conformément aux codes électriques locaux.
3
Branchez le fil blanc au fil de ligne à neutre avec un écrou de fil.
4
Branchez le fil noir au fil ligne électrique chaud avec un serre-fils.
5
Montez l'embase de fixation sur la plaque de montage et le fixer avec les vis de réglage.
6
Installer le tube bougie en se glissant à travers le socket.
7
Vissez la lampe dans la douille. Reportez-vous à l'étiquette sur la douille de lampe Puissance max pour plus d'informations.
8
Installez l'ombre par encliquetage sur l'ampoule.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A SOMBRA
8
CABLE NEUTRO
BOMBILLA
CABLE BLANCO
7 VELA DEL TUBO
CAJA ELÉCTRICA 1
6
1 MONTAJE PLACA MONTAJE PLACA DE TORNILLO
FIXTURE 5
CABLE CALIENTE CABLE NEGRO
TORNILLO FIJARSE
1
Fije la placa de montaje a la caja eléctrica con los dos tornillos de la placa de montaje proporcionado.
2
Conecte el cable de tierra a una tierra artefacto adecuado de acuerdo a los códigos eléctricos locales.
3
Conecte el cable blanco del portalámparas al cable de energía de la línea neutral con un tapón de alambre.
4
Conecte el cable negro del portalámparas al cable de alimentación de línea caliente con un tapón de alambre.
5
Mount the fixture base onto the mounting plate and secure it with the set screws.
6
Monte la base del aparato en la placa de montaje y fíjela con los tornillos de fijación.
7
Atornille la lámpara en el zócalo. Consulte la etiqueta del casquillo de la lámpara para obtener información Potencia Max.
8
Instale la persiana mediante el ajuste a la bombilla.
Secure the mounting plate to the junction box. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. Connect the white ...
Sophie 1, 2, 3, and 4 Light Vanity Strip. 1.1. VS47002-VS47003-VS47004-WB1724. VS47002,VS47003,. VS47004,WB1724. Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground
Connecter le fil blanc du luminaire (carré et / ou rigide) pour le fil de ligne à neutre ... Parfaitement placer tous les fils dans la boîte électrique, le montage d'essai ...
sujeción en caja de salida de casa. Instale la lámpara enroscándolo en la toma de corriente. Consulte la etiqueta del casquillo de la lámpara para obtener.
Install and secure the string of beads by hooking them to the top and bottom of the fixture. Install the candle tube by slipping through the socket. Install candle ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamps into the sockets. Refer to the ...
CABLE NEGRO. CAJA ELÉCTRICA. PLACA DE. MONTAJE. LÁMPARA. PRECAUCIÓN: RIESGO DE INCENDIO. Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los
Place the shade and spacer over the socket and secure them in place by screwing the collar nut onto the socket. Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. Install the cover to the fixture arm an
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground in accordance to local ...
Connect the white fixture wire to the neutral power line wire with a wire nut. Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws. Install th
Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. Connect the white driver wire to the neutral power line wire with a wire nut. Connect the black driver wire to the hot power line wire with a wire nut. Moun
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket; repeat for remaining sockets. Screw the ...
Connectez le fil de terre du luminaire à un terrain approprié conformément ... Connectez le fil noir du luminaire au fil ligne électrique chaud avec un serre-fils.