Sophie 1, 2, 3, and 4 Light Vanity Strip. 1.1. VS47002-VS47003-VS47004-WB1724. VS47002,VS47003,. VS47004,WB1724. Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. Connect the white ...
Wall GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for damp locations.
1A LAMP
7
COLLAR NUT NEUTRAL WIRE SPACER
ELECTRICAL BOX
WHITE WIRE ALLEN WRENCH
1
SHADE 1 6
MOUNTING PLATE 5 MOUNTING PLATE SCREW
SOCKET HOT WIRE BLACK WIRE FIXTURE SCREW
1
Secure the mounting plate to the electrical box with the two mounting plate screws.
2
Connect the fixture ground wire to a suitable ground in accordance to local electrical codes.
3
Connect the white fixture wire to the neutral power line wire with a wire nut.
4
Connect the black fixture wire to the hot power line wire with a wire nut.
5
Mount the fixture base onto the mounting plate and secure it with the fixture screws.
6
Install the shade and spacer by placing them over the socket and securing them with the collar nut.
7
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. If necessary, repeat steps 6 and 7 for remaining sockets.
1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A 7 AMPOULE
ÉCROU À COLLIER FIL NEUTRE ESPACEUR
BOÎTE ÉLECTRIQUE
FIL BLANC
1
CLÉ ALLEN ABAT-JOUR
1 6
PLAQUE DE MONTAGE 5 VIS DE MONTAGE
DOUILLE FIL CHAUD FIL NOIR VIS DE LUMINAIRE 1
Fixez la plaque de montage à la boîte électrique avec les deux vis de montage.
2
Connectez le fil de terre du luminaire à un terrain approprié conformément aux codes électriques locaux.
3
Connectez le fil blanc du luminaire au fil de ligne à neutre avec un écrou de fil.
4
Connectez le fil noir du luminaire au fil ligne électrique chaud avec un serre-fils.
5
Montez l'base du luminaire sur la plaque de montage et le fixer avec les vis de luminaire.
6
Installer l'abat-jour et l'espaceur en les plaçant sur le douille et les fixant avec l'écrou à collier.
7
Vissez l'ampoule dans la douille. Consulter l'étiquette sur la douille de lampe pour information Max Wattage. Si nécessaire, répétez les étapes 6 et 7 pour douille restante.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
BOMBILLA
7
TUERCA DE COLLAR CABLE NEUTRO CAJA ELÉCTRICA
CABLE BLANCO
ESPACIADOR
LLAVE DE ALLEN
1
PANTALLA 1 6
PLACE DE MONTAJE 5 TORNILLO DE MONTAJE
ENCHUFE CABLE CALIENTE CABLE NEGRO TORNILLO DE LA LÁMPARA 1
Fije la placa de montaje a la caja eléctrica con los dos tornillos de la placa de montaje.
2
Conecte el cable de tierra a una tierra artefacto adecuado de acuerdo a los códigos eléctricos locales.
3
Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con un tapón de alambre.
4
Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre.
5
Monte el base de la lámpara en la placa de montaje y fíjela con los tornillos de la lámpara.
6
Instalar la pantalla y el espaciador por colocarlos sobre el enchufe y asegurándolos con la tuerca de collar.
7
Enrosque la bombilla en el enchufe. Consulte la etiqueta en el enchufe de la lámpara para información sobre la Max Wattage. Si es necesario, repita los pasos 6 y 7 para el enchufe restante.
Secure the mounting plate to the junction box. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. Connect the white ...
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket; repeat for remaining sockets. Screw the ...
Connectez le fil de terre du luminaire à un terrain approprié conformément ... Connectez le fil noir du luminaire au fil ligne électrique chaud avec un serre-fils.
Mount the fixture base onto the mounting plate and secure it with the fixture screws. Place the shade over ... without notification. A Generation Brands Company.
Max Potencia.ctamente sobre el enchufe y asegúrelo en su lugar montándolo en el gancho de la lámpara correspondiente. 1. 2. 3. 4. 5. 6. PRECAUCIÃN: RIESGO DE INCENDIO. Este producto debe instalarse de acuerdo con el código de instalación aplica
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors.
Mount the fixture base onto the mounting plate and secure it with the fixture ... Monte la base de la lámpara en la placa de montaje y fijarlo con el tornillo de la ...
Connect the fixture ground wire to a suitable ground in accordance to local ... Connect the white fixture wire to the neutral power line wire with a wire nut.
Connect the white fixture wire to the neutral power line wire with a wire nut. Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws. Install th
If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely ... If any part is missing or damaged, do not attempt to.
Refer to the label on the lamp socket for Max Wattage information. Install and secure the string of beads by hooking them to the top and bottom of the fixture.
the applicable installation code by a person familiar with the construction and operation ... código de instalación aplicable por una persona familiarizada con la ...
Installer et fixer la chaîne de perles en les accrochant au haut et au bas de ... le bas de l'appareil et à la police, puis accrocher la basse chaîne de perles à la.
Ensure that the spun pan rests properly on top of the shade. Screw the ... with the construction and operation of the product .... A Generation Brands Company.