Vanity Strip GENERAL PRODUCT INFORMATION: This product is listed by one of the following “Nationally Recognized Testing Laboratory”
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is suitable for damp locations.
Use minimum 90°c supply conductors.
This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
1A 1A
SHADE TOOL LAMP
7 COLLAR NUT
6 SPACER
MOUNTING PLATE SCREW MOUNTING PLATE
SHADE
1
SOCKET
3
JUNCTION BOX
4 FIXTURE SCREW
1 5 ALLEN WRENCH
1
Secure the mounting plate to the electrical box with the two mounting plate screws.
2
Connect the fixture ground wire to a suitable ground in accordance to local electrical codes.
3
Connect the white fixture wire to the neutral power line wire with a wire nut.
4
Connect the black fixture wire to the hot power line wire with a wire nut.
5
Mount the fixture base onto the mounting plate and secure it with the fixture screws using an Allen wrench.
6
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket using the shade tool. Repeat for multiple shades.
7
Screw the lamp(s) into the socket(s). Refer to the label on the lamp socket for Max Wattage information.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A OUTIL DE ABAT-JOUR
AMPOULE
7 ECROU DE COLLIER
6 ESPACEUR
VIS DE MONTAGE PLAQUE DE MONTAGE
ABAT-JOUR
1
DOUILLE
3
BOÎTE JONCTION
4 VIS DE LUMINAIRE
1 5 CLÉ ALLEN
1
Fixez la plaque de montage à la boîte électrique avec les deux vis de montage.
2
Connectez le fil de terre du luminaire à un terrain approprié conformément aux codes électriques locaux.
3
Connectez le fil blanc du luminaire au fil de ligne à neutre avec un écrou de fil.
4
Connectez le fil noir du luminaire au fil ligne électrique chaud avec un serre-fils.
5
Montez la base de fixation sur la plaque de montage et le fixer avec les vis de luminaire à l'aide d'une clé Allen.
6
Placez l'abat-jour et l'espaceur sur le socket, puis fixez-les en place en vissant l'écrou de collier sur la douille en utilisant l'outil de l'abat-jour. Répétez l'opération pour plusieurs abat-jour.
7
Visser la/les ampoule (s) dans la/les douille (s). Reportez-vous à l'étiquette sur la douille de la lampe pour obtenir des informations Max Puissance.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A HERRAMIENTA DE LA PANTALLA
BOMBILLA
7 TUERCA DE COLLAR
6 ESPACIADOR
TORNILLO DE MONTAJE PLACE DE MONTAJE
PANTALLA
1
ENCHUFE
3
CAJA ELÉCTRICA
4 1 TORNILLO DE LA LÁMPARA
5 LLAVE DE ALLEN
1
Fije la placa de montaje a la caja eléctrica con los dos tornillos de la placa de montaje.
2
Conecte el cable de tierra a una tierra artefacto adecuado de acuerdo a los códigos eléctricos locales.
3
Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con un tapón de alambre.
4
Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre.
5
Monte la base del aparato en la placa de montaje y fijarlo con los tornillos de lámpara con una llave Allen.
6
Coloque la pantalla y el espaciador sobre el enchufe, luego fijarlos en su lugar atornillando la tuerca de sombra en el enchufe con la herramienta de la pantalla. Repita el procedimiento para múltiples pantallas.
7
Atornille la(s) bombilla(s) en la(s) enchufe(s). Consulte la etiqueta del casquillo de la lámpara para obtener información Max Potencia.ctamente sobre el enchufe y asegúrelo en su lugar montándolo en el gancho de la lámpara correspondiente.
Max Potencia.ctamente sobre el enchufe y asegúrelo en su lugar montándolo en el gancho de la lámpara correspondiente. 1. 2. 3. 4. 5. 6. PRECAUCIÃN: RIESGO DE INCENDIO. Este producto debe instalarse de acuerdo con el código de instalación aplica
Secure the mounting plate to the junction box. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. Connect the white ...
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket; repeat for remaining sockets. Screw the ...
Sophie 1, 2, 3, and 4 Light Vanity Strip. 1.1. VS47002-VS47003-VS47004-WB1724. VS47002,VS47003,. VS47004,WB1724. Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground
Connectez le fil de terre du luminaire à un terrain approprié conformément ... Connectez le fil noir du luminaire au fil ligne électrique chaud avec un serre-fils.
Mount the fixture base onto the mounting plate and secure it with the fixture screws. Place the shade over ... without notification. A Generation Brands Company.
Mount the fixture base onto the mounting plate and secure it with the fixture ... Monte la base de la lámpara en la placa de montaje y fijarlo con el tornillo de la ...
Connect the fixture ground wire to a suitable ground in accordance to local ... Connect the white fixture wire to the neutral power line wire with a wire nut.
If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely ... If any part is missing or damaged, do not attempt to.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors.
Installation should be carried out in accordance with the latest edition of the National Wiring Regulations. If in doubt, consult a qualified electrician. â¢. The LED Strip operates at 12V DC. A 12V DC LED Driver is required (not included). â¢. Whe
To install the LED Driver please refer to its own instructions. ... Slide a length of the heat shrink sleeve onto the end of the strip to be connected to the LED Driver.
trajet, d'offrir aux flâneurs des tro oirs plus larges pouvant accueillir des terrasses ... centrale ainsi que des nouveaux tro oirs, sur une surface de 60.000 mètres.