Outdoor GENERAL PRODUCT INFORMATION: CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is listed by one of the following “Nationally Recognized Testing Laboratory” These fixtures are intended to be installed utilizing NEC compliant junction boxes.
Use minimum 90°c supply conductors.
This product is suitable for damp locations. This product may be dimmed with a standard incandescent dimmer.
1A MOUNTING PLATE SCREW
8
7
FIXTURE BASE
CLIP
MOUNTING PLATE MOUNTING PLATE STUD
1 2
CORNER GLASS PANEL
1 CAP NUT
9
9 LAMP
2 3
1 THREADED PIPE
1
5
SHADE BRACKET SCREW SIDE GLASS PANEL
BRACKET WASHER
BOTTOM GLASS PANEL
DECORATIVE CUP
11 10
FRAME SCREW
1
Install the bottom and corner glass panels to the frame by carefully sliding them into the frame and securing them using the brackets and bracket screws as shown.
2
Install the side glass panels by carefully sliding them into the frame and securing them using the clips as shown.
3
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
4
Secure the mounting plate to the junction box with two mounting plate screws.
5 1
Screw the threaded pipe to the bottom of the fixture base.
6
Connect the fixture to a suitable ground in accordance to local electrical codes.
7
Connect the white fixture wire to the neutral power line wire with a wire nut.
8
Connect the black fixture wire to the hot power line wire with a wire nut.
9
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts on the mounting plate studs.
10
Place the shade and washer onto the threaded pipe and secure them in place by screwing on the decorative cup.
11
Swing the frame closed and secure it in place by screwing the frame screw into the fixture base. 1
1.0
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c.
1A VIS DE MONTAGE
8
7
BASE DE LUMINAIRE
CLIP
PLAQUE DE MONTAGE GOUJON DE MONTAGE
1 2
PANNEAU DE VERRE DE COIN
1 ECROU CAPUCHON
9
9 AMPOULE
2 3
1 TUYAU FILETÉ
1
5
ABAT-JOUR VIS DE SUPPORT VERRE DE PANNEAU LATÉRAL
SUPPORT RONDELLE
ANNEAU DE VERRE DE BAS
COUPE DECORATIVE
11 10
VIS DE CADRE
1
Installez les bas et verre de coin panneaux au cadre en faisant glisser avec précaution dans le cadre et les fixer à l'aide des crochets et des vis du support comme indiqué.
2
Installez les panneaux de verre de côté en les faisant glisser avec précaution dans le cadre et les fixer à l'aide des clips comme indiqué.
3
Vissez l’ampoules dans les douilles. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
4
Fixer la plaque de montage sur le boîte de jonction avec deux vis de montage.
5 1
Vissez le tuyau fileté au fond de la base de luminaire.
6
Connecter le luminaire à un terrain approprié conformément aux codes électriques locaux.
7
Connecter le fil blanc de luminaire (carré et / ou rigide) pour le fil de ligne à neutre avec un écrou de fil.
8
Connecter le fil noir de luminaire (rond et / ou lisse) au fil de la ligne d'alimentation hot avec un écrou de fil.
9
Placez la base de luminaire sur les goujons de montage et fixez-le en vissant les écrous sur les goujons de montage.
10
Placez l'abat-jour et la rondelle sur le tuyau fileté et fixez-les en place par vissage sur la coupe décorative.
11
Faites pivoter le cadre fermé et le fixer en place par vissage de la vis de cadre dans la base de luminaire.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min.
1A TORNILLO DE MONTAJE
8
7
BASE DE LA LÁMPARA
CLIP
PLACA DE MONTAJE ESPARRAGO DE MONTAJE
1 2
1 TUERCA CAPUCHON
PANEL DE VIDRIO DE LA ESQUINA
9
9 BOMBILLA
2 3
1
CONECTADOR ROSCADO
1
5
SHADE TORNILLO SOPORTE DE SOPORTE PANEL DE VIDRIO LATERAL
ARANDELA
PANEL DE VIDRIO DEL FONDO
COPA DECORATIVA
11 10
TORNILLO DEL MARCO
1
Instale los paneles de vidrio del fondo y esquina al marco deslizando cuidadosamente en el marco y asegurándolos con los soportes y tornillos del soporte como se muestra.
2
Instalar los paneles de vidrio del lado deslizándolos cuidadosamente en el marco y asegurar usando los clips como se muestra.
3
Atornille las bombillas en los enchufes. Consulte la etiqueta del casquillo de la lámpara para obtener información Max Potencia.
4
Fije la placa de montaje a la caja de junctura con dos tornillos de la placa de montaje.
5 1
Atornillar el tubo roscado a la parte inferior de la base de la lámpara.
6
Conecte la lámpara a una puesta a tierra adecuada de acuerdo a los códigos eléctricos locales.
7
Conecte el cable blanco de la lámpara (cuadrado y / o rígido) al cable de la línea de alimentación neutra con una tuerca para cable.
8
Conecte el cable negro de la lámpara (redonda y / o suave) al cable de la línea eléctrica caliente con una tuerca para cable.
9
Coloque la base de la lámpara en los esparragos de montaje y fijarlo en su lugar atornillando las tuercas capuchon en los esparragos de montaje.
10
Coloque la pantalla y la arandela en el tubo roscado y fijarlos en su lugar atornillando en el coupe decorativo.
11
Gire el marco cerrado y seguro en su lugar atornillando el tornillo de marco en la base de la lámpara. Empuje la pantalla en la base de la lámpara y girarla para que encaje en su lugar.
Secure the mounting plate to the junction box. ... Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 4. 1. 1.
á. Conecte el cable negro de la l mpara al cable de alimentación de línea caliente con un tapón de alambre. á. Alinee las ranuras en el base de la l mpara para ...
Place the fixture base over the threaded nipple and secure it in place with the cap nut. Screw the lamps into the sockets. Refer to the label on the lamp socket for ...
Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threaded pipe and secure it in place with the washer and hex nut ...
Cadence 2 Light Flush Mount. 1.1. FM390. Ceiling. FM390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC ...
Installation Instructions for. Hamlet 2 Light Semi-Flush Mount. 1.0. SF325. SF325. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
... on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together. 1. 2.
Connect the fixture to a suitable ground in accordance with local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Install the shades by placing them over the sockets, then ...
Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut. Place the decorative cup ...
Lennon 3 Light Semi-Flush Mount. 1.0. SF339. SF339. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Marquer les emplacements des trous d'ancre sur la plaque de montage et ... Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un ...
1A. 3. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards ... Connecter le fil noir du luminaire (rond et
applicable installation code by a person familiar with the construction ... Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
Lennon 5 Light Semi-Flush Mount. 1.0. SF340. SF340. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Place the fixture base onto the mounting plate studs and secure it in place by screwing the cap nuts onto the studs. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information. Place the shade onto the threade
the applicable installation code by a person familiar with the ... Use minimum 90°c supply conductors. 4. 1. 2. 3. 3. 4. CAP NUT. THREADED NIPPLE. 3 ...