Follow enclosed supplement installation instructions for electrical and fixture installation onto junction box. Install the threaded pipes by screwing them into ...
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations. Incandescent lamps may be dimmed with a standard incandescent dimmer. LED lamps may be dimmed with a LED dimmer. Consult lamp manufacturer for additional information.
Use minimum 90°c supply conductors.
1A HEX NUTS
CAUTION: Do not rotate the frame when installing the glass tubes.
1
THREADED PIPE GLASS TUBE
2
GLASS TUBE BASE SOCKET LAMP
3
4
NOTE: Please refer to step 4 before installing the glass tubes.
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto junction box.
2
Install the threaded pipes by screwing them into center of the fixture.
3
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
4
Install the glass tubes over the sockets and secure them in place by screwing them into the glass tube base. Caution: Carefully align the threads of the glass tube to the glass tube base and make sure they are engaged correctly.
1
1.1
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c. 1A ECROUS HEX
ATTENTION: Lors de l'installation des tubes en verre, ne pas faire pivoter le cadre.
1
TUYAU FILETÉ TUBES DE VERRE
2
BASE DE TUBES DE VERRE DOUILLE AMPOULE
3
4
REMARQUE: reportezvous à l'étape 4 avant d'installer les tubes en verre.
1
Suivez les instructions d'installation des accessoires ci-jointes pour l'installation des appareils électriques et des appareils sur la boîte de jonction.
2
Installez les tuyaux filetés en les vissant au centre de luminaire.
3
Visser l'ampoules dans les douilles. Reportez-vous à l'étiquette indiquée sur la douille de l'ampoule pour obtenir des informations sur le débit max.
4
Installer les tubes de verre sur les douilles et les fixer en les vissant dans les base de tubes de verre. Attention: aligner soigneusement les fils du tube de verre sur la base du tube en verre et s'assurer qu'ils sont bien engagés.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min. 1A TUERCAS HEX
PRECAUCIÓN: Cuando instale los tubos de vidrio, no gire el marco.
1
TUBO ROSCADO TUBO DE VIDRIO
2
BASE DEL TUBO DE VIDRIO ENCHUFE BOMBILLA
3
4
NOTA: Consulte el paso 4 antes de instalar los tubos de vidrio.
1
Siga las instrucciones adjuntas de instalación del suplemento para la instalación eléctrica y de los accesorios en la caja de conexiones.
2
Instale los tubos roscados atornillándolos en el centro del aparato.
3
Atornille las bombillas en los enchufes. Consulte la etiqueta en el enchufe de la lámpara para obtener información sobre la potencia máxima.
4
Instale los tubos de vidrio sobre los enchufes y fíjelos en su lugar atornillándolos en los bases de los tubos de vidrio. Precaución: alinee cuidadosamente las roscas del tubo de vidrio con la base del tubo de vidrio y asegúrese de que estén bien acopladas.
3
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077 800.323.3226 - 847.626.6300
the fixture screws. Install the silicone pads over the sockets. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
Install the inner and outer rings to each pendant using the thumb screws. ... installation instructions for electrical and fixture installation onto house outlet box. 1.
additional information. CAUTION RISK OF FIRE. -. This product must be installed in accordance with the applicable installation code by a person familiar with the.
Screw the anchor screws into the anchors ensuring one anchor washer and screw secure the safety cable. Connect the ... Connect the white fixture wire (square and/or rigid) to the neutral power line wire with a wire nut. Connect ... VIS COURT.
Install the tethered chains by hooking them to the bottom of the fixture, then place the cups onto the threads under the sockets and secure them in place by ...
... the lamp socket for Max Wattage information. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. 1.
Connect the fixture to a suitable ground in accordance to local electrical codes. ... Neatly place all the wires into the junction box, place the canopy onto the ...
installation onto house outlet box. STEM. SEMI-FLUSH MOUNT ... This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Installer un lien rapide sur la boucle de luminaire et la chaîne, puis un autre lien ... Tisser le cordon à travers la chaîne, la dais et hors de la boîte électrique.
instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone. Conductores de alimentacion ...
Determine the height of the fixture with the provided stems and chain/loop, then assemble them by screwing them together. Insert the socket assembly through ...
código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de ...