Chandelier CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
Use minimum 90°c supply conductors.
This product is safety listed for damp locations. JUNCTION BOX
1A
MOUNTING PLATE
7
3
SWAG HOOK
6 THREADED NIPPLE
CORD CORD CLIP
2
11
CANOPY
CLIP SCREW
CAP NUT
8
CANOPY
SOCKET
SHADE COLLAR NUT
9 LAMP
10 SHADE TOOL
1
Determine the wanted height of the fixture by feeding the cord through the canopy and moving the cord up or down.
2
Place the cord in between the two cord clips and secure it in place using the clip screws.
3
Trim the cord leaving enough for electrical connections. From the end of the cord, strip the insulation 4” and then strip the end of the wires. Note: Make sure not to nick the inner wires. Repeat for remaining cords.
4
Secure the mounting plate to the junction box.
5
Connect the fixture to a suitable ground in accordance to local electrical codes.
6
Connect the white fixture wires (square and/or rigid) to the neutral power line wire with a wire nut.
7
Connect the black fixture wires (round and/or smooth) to the hot power line wire with a wire nut.
8
Neatly place all the wires into the junction box, place the canopy onto the threaded nipple, and secure it in place by screwing the cap nut onto the threaded nipple
9
Place the shade onto the socket and secure it in place by screwing the collar nut onto the socket using the shade tool. Repeat for remaining shades.
10
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage information.
11
Optional: Use enclosed instructions for Swag Hook installation.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
BOÎTE DE JONCTION
1A
PLAQUE DE MONTAGE
7
3
SWAG HOOK
6 ATTACHE FILETÉ
CORDON PINCE DE CORDON VIS DE LA PINCE
2
11
DAIS ECROU CAPUCHON
8
DAIS
DOUILLE
ABAT-JOUR ECROU COLLIER
9 AMPOULE
10 OUTIL D’ABAT-JOUR
1
Déterminer la hauteur désirée de luminaire en alimentant le cordon à travers la dais et en déplaçant le cordon vers le haut ou vers le bas.
2
Placez le cordon entre les deux pince de la moelle et le fixer en place à l'aide des vis de pince.
3
Coupez le cordon en laissant suffisamment pour les connexions électriques. Dès la fin de la corde, le dénuder 4”, puis dénuder l'extrémité des fils. Remarque: Assurez-vous de ne pas entailler les fils intérieurs. Répétez l'opération pour les cordons restants.
4
Fixer la plaque de montage à la boîte de jonction.
5
Connecter le luminaire à un terrain approprié conformément aux codes électriques locaux.
6
Connecter les fils de luminaire blanc (carré et / ou rigides) au fil de la ligne d'alimentation neutre avec un écrou de fil.
7
Connecter les fils de luminaire noir (ronds et / ou lisses) au fil de la ligne d'alimentation chaude avec un écrou de fil.
8
Placer soigneusement tous les fils dans la boîte de jonction, placez la dais sur le attache fileté et le fixer en place en vissant l'écrou capuchon sur le attache fileté
9
Placez l'abat-jour sur le douille et le fixer en place par vissage de l'écrou de collier sur la douille en utilisant l'outil de l'abat-jour. Répéter pour les abat-jours restantes.
10
Vissez l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la prise d'information Max Wattage.
11
Facultatif: Utilisez les instructions fournies pour l'installation Swag Hook.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
CAJA DE JUNCTURA
1A
PLACA DE MONTAJE
7
3
SWAG HOOK
6 CONECTADOR ROSCADO
CORDÓN PINZA DEL CABLE
2
11
DOSEL
TORNILLO DE LA PINZA
TUERCA CAPUCHON
8
DOSEL
ENCHUFE
PANTALLA TUERCA DE COLLAR
9 BOMBILLA
10
HERRAMIENTA DE LA PANTALLA
1
Determine la altura deseada de la lámpara alimentando el cable a través del dosel y moviendo el cable hacia arriba o hacia abajo.
2
Coloque el cable entre las dos pinzas de la cuerda y fijarla en su lugar con los tornillos de las pinzas.
3
Recorte el cable dejando suficiente para las conexiones eléctricas. Desde el extremo del cable, retire el aislamiento 4" y después pelar el extremo de los cables. Nota: Asegúrese de no dañar los cables internos. Repetir para los cables restantes.
4
Fije la placa de montaje a la caja de conexiones.
5
Conecte la lámpara a una puesta a tierra adecuada de acuerdo con los códigos eléctricos locales.
6
Conecte los cables de la lámpara blanca (cuadrados y / o rígidos) al cable neutro línea eléctrica con una tuerca de cable.
7
Conecte los cables de la lámpara negra (redondos y / o lisas) al cable de alimentación de línea caliente con una tuerca de cable.
8
Cuidadosamente colocar todos los cables en la caja de conexiones, coloque el dosel en el conectador roscado, y fijarla en su lugar enroscando la tuerca capuchon en el conectador roscado
9
Coloque la pantalla en el enchufe y asegurarlo en su lugar enroscando la tuerca de collar en el enchufe usando la herramienta de pantalla. Repita para las pantallas restantes.
10
Atornille las bombillas en los enchufes. Consulte la etiqueta en la toma de información Max Potencia.
11
Opcional: Utilice instrucciones adjuntas para la instalación Swag Hook.
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage information. Optional: Use enclosed instructions for Swag Hook installation.
Determine the height of the fixture with the provided stems and chain/loop, then assemble them by screwing them together. Insert the socket assembly through ...
Connect the fixture to a suitable ground in accordance to local electrical codes. ... Neatly place all the wires into the junction box, place the canopy onto the ...
installation onto house outlet box. STEM. SEMI-FLUSH MOUNT ... This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
L. This product is suitable for dry locations only. This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
Installer et fixer la chaîne de perles en les accrochant au haut et au bas de ... le bas de l'appareil et à la police, puis accrocher la basse chaîne de perles à la.
Ensure that the spun pan rests properly on top of the shade. Screw the ... with the construction and operation of the product .... A Generation Brands Company.
Installation Instructions for ... Feed the fixture wires through the stem assembly and screw the stem ... box, place the canopy onto the mounting plate, and secure it in place with the ... Refer to the label on the lamp socket for Max Wattage informa
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes . Consulte la etiqueta del casquillo de la lámpara para obtener información Max.
R. T. L. This product is suitable for dry locations only. This product may be ... Follow enclosed supplement installation instructions for electrical and fixture ...
Instalar los seguidores de la vela por su inclusión en la parte superior de los tubos de la vela. . Consulte la etiqueta del casquillo de la lámpara para obtener ...
Pickering Lane 3 Light Chandelier. 1.1. F2782-3. F2782. 1A. SHADE. SHADE HOLDER. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Install ring onto fixture with ball cap screws. Insta
Follow enclosed supplement installation instructions for electrical and fixture installation ... Refer to the label on the lamp socket for Max Wattage information.
junction boxes. This product is suitable for dry locations only. This product may be dimmed with a standard incandescent dimmer. Feed the cord through the ...
código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de ...
Installer un lien rapide sur la boucle de luminaire et la chaîne, puis un autre lien ... Tisser le cordon à travers la chaîne, la dais et hors de la boîte électrique.