Install the tethered chains by hooking them to the bottom of the fixture, then place the cups onto the threads under the sockets and secure them in place by ...
Chandelier CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations.
Use minimum 90°c supply conductors.
Incandescent lamps may be dimmed with a standard incandescent dimmer. LED lamps may be dimmed with a LED dimmer. Consult lamp manufacturer for additional information. This instruction shows a typical installation.
1A 7
FIXTURE LOOP HUB HOOK
2
CHAIN STEM
6
LAMP
5
CANDLE FOLLOWER
4
CANDLE TUBE
3
SOCKET
1 THREAD
8
CUP FINIAL TETHERED CHAINS
1
Feed the fixture wires through the stem and screw the stem onto the fixture.
2
Feed the fixture wires through the hub and fixture loop, then screw the hub onto the stem.
3
Install the chains to hub and fixture by securing the hooks to the hub and fixture.
4
Install the candle tubes by sliding them over the sockets.
5
Install the candle followers by placing them on top of the candle tubes.
6
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage Information.
7
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
8
Install the tethered chains by hooking them to the bottom of the fixture, then place the cups onto the threads under the sockets and secure them in place by screwing each finial onto the corresponding threads.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A 7
BOUCLE DE LUMINAIRE MOYEU CROCHET
2
CHAÎNE TIGE
6
AMPOULE
5
SUIVEUR DE BOUGIE
4
TUBE BOUGIE
3
DOUILLE
1 FILETS
8
COUPE FLEURON CHAÎNES CONNECTÉES
1
Nourrir les fils de luminaire à travers la tige et visser la tige sur le luminaire.
2
Nourrir les fils de luminaire à travers la moyeu et boucle de luminaire, puis visser le moyeu sur la tige.
3
Installez les chaînes à moyeu et montage en fixant les crochets au moyeu et luminaire.
4
Installez les tubes de bougies en les faisant glisser sur les douilles.
5
Installez les suiveurs de bougie en les plaçant au-dessus des tubes de bougies.
6
Vissez l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille pour Max Wattage information.
7
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et luminaire sur la boîte de sortie de la maison.
8
Installer les chaînes connectées en les accrochant au fond de luminaire, puis placer les coupes sur les filets sous les orbites et les fixer en place en vissant chaque fleuron sur les filets correspondants.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A 7
BUCLE DE LA LÁMPARA EJE GANCHO
2
CADENA TALLO
6
BOMBILLA
5
SEGUIDOR DE VELA
4
TUBO DE VELA
3
ENCHUFE
1 ROSCAS
8
COPA FINIAL CADENAS CONNECTEDAS
1
Alimentar a los cables de la lámpara a través del tallo y atornillelo el tallo en la lámpara.
2
Alimentar a los cables de la lámpara a través del eje y bucle de la lámpara, luego atornille el eje sobre el tallo.
3
Instalar las cadenas a hub y la lámpara asegurando los ganchos al eje y la lámpara.
4
Instalar los tubos de vela deslizándolos sobre los enchufes.
5
Instalar los seguidores de la vela que los coloca en la parte superior de los tubos de la vela.
6
Atornille las bombillas en el enchufe. Consulte la etiqueta en la toma de Max Información de Potencia.
7
Siga las instrucciones de instalación del suplemento cerrados para la instalación eléctrica y el accesorio sobre la caja de salida de la casa.
8
Instalar las cadenas conectadas enganchando a la parte inferior del dispositivo y, a continuación colocar las copas en las roscas bajo los enchufes y fijarlos en su lugar enroscando cada finial ornamental en las roscas correspondientes.
Refer to the label on the lamp socket for Max Wattage information. Install and secure the string of beads by hooking them to the top and bottom of the fixture.
código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de ...
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage information. Optional: Use enclosed instructions for Swag Hook installation.
Installer et fixer la chaîne de perles en les accrochant au haut et au bas de ... le bas de l'appareil et à la police, puis accrocher la basse chaîne de perles à la.
Ensure that the spun pan rests properly on top of the shade. Screw the ... with the construction and operation of the product .... A Generation Brands Company.
Install the bottom tier to the top tier by screwing the fixture arms to the swivels and bottom of the top tier. Assemble the top tier by screwing the fixture arms to the ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 1. 2. 3.
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes . Consulte la etiqueta del casquillo de la lámpara para obtener información Max.
F2942-6. Chandelier. F2942/6. Install the candle followers by placing them on top of the ... This product may be dimmed with a standard incandescent dimmer.
Mount and secure all arms to the top of the fixture by tightening caps. Mount and secure the frame to the arms by tightening the cap screws and nuts. Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. 1
Installez les tubes de bougies en les glissant sur les douilles. Installez les suiveurs de la bougie au sommet des tubes de bougies. Vissez l'ampoules dans les ...
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SMALL ORNAMENT. THUMB SCREW. 7. F
G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandescent dimmer. This instru
3 months. If a warning code appears and the corrective action mentioned is calibration this menu guides through .... A new power supply can be ordered with the following reference number: 817804. Wall Unit ...... 14 Spécifications techniques .
Beverly is built for a purpose: to measure dissolved oxygen at-line as well as .... current consumption, it is recommended to to unplug Beverly after charging from.
the fixture screws. Install the silicone pads over the sockets. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.