Chandelier GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for dry locations only.
1A 5
STEM ASSEMBLY
1 HUB ASSEMBLY
4 SHADE
INDIVIDUAL STEM
3 LAMP
1 CANDLE TUBE
2
SOCKET
FIXTURE
6 DECORATIVE STRAND
1
Screw the individual stem to the fixture, then place the stem assembly over the individual stem and secure them in place by screwing the hub assembly onto the individual stem.
2
Install the candle tubes by slipping them through the sockets.
3
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
4
Install the shade by placing it over the lamp. Repeat steps 2-4 for remaining shades.
5
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
6
Install the decorative strand by hooking it to the fixture as shown on drawing.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A 5
TIGE ASSEMBLÉE
1 ASSEMBLÉE DU MOYEU
4 ABAT-JOUR
TIGE INDIVIDUEL
3 AMPOULE
1 TUBE BOUGIE
2
DOUILLE
LÁMPARA
6
CHAPELET DÉCORATIF
1
Vissez la tige unique à l'armature, puis placer l'ensemble de la tige sur la tige unique et fixez-les en place en la vissant à l'Assemblée de moyeu sur la tige unique.
2
Installer les tubes de bougie en les glissant à travers les douille.
3
Vissez le ampoule dans le douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
4
Installer l'abat-jour en le plaçant sur la ampoule. Répétez les étapes 2 à 4 pour les autres douilles.
5
Suivez supplément ci-joint des instructions électriques et installation d'accessoires dans la boîte de prise de maison.
6
Installer le brin décoratif en l'accrochant à l'armature comme indiqué sur le dessin.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A 5
ASAMBLEA DE TALLO
1 ASAMBLEA DE EJE
4 PANTALLA
TALLO INDIVIDUAL
3 BOMBILLA
1 TUBO DE VELA
2
ENCHUFE
LUMINAIRE
6
FILAMENTO DECORATIVO
1
Atornillar el tallo a la lámpara, luego coloque la asamblea de tallo sobre el tallo individual y bloquéelas atornillando el la asamblea de eje en el tallo individual.
2
Instale el tubode vela deslizándolo a través de el enchufe.
3
Atornille la bombilla en el enchufe. Consulte la etiqueta en el zócalo de la lámpara para obtener información de Max Wattage.
4
Instale la pantalla colocándola sobre la bombilla. Repita los pasos 2-4 para enchufes restantes.
5
Siga las instrucciones de Instalación incluido suplemento para eléctricos y instalación de la lámpara en la caja de enchufe de casa.
6
Instale el filamento decorativo enganchándolo en la lámpara como se muestra en el dibujo.
código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de ...
Installer et fixer la chaîne de perles en les accrochant au haut et au bas de ... le bas de l'appareil et à la police, puis accrocher la basse chaîne de perles à la.
Ensure that the spun pan rests properly on top of the shade. Screw the ... with the construction and operation of the product .... A Generation Brands Company.
Mount and secure all arms to the top of the fixture by tightening caps. Mount and secure the frame to the arms by tightening the cap screws and nuts. Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. 1
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes . Consulte la etiqueta del casquillo de la lámpara para obtener información Max.
Instalar los seguidores de la vela por su inclusión en la parte superior de los tubos de la vela. . Consulte la etiqueta del casquillo de la lámpara para obtener ...
L. This product is suitable for dry locations only. This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
junction boxes. This product is suitable for dry locations only. This product may be dimmed with a standard incandescent dimmer. Feed the cord through the ...
R. T. L. This product is suitable for dry locations only. This product may be ... Follow enclosed supplement installation instructions for electrical and fixture ...
código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de ...
Refer to the label on the lamp socket for Max Wattage information. Install and secure the string of beads by hooking them to the top and bottom of the fixture.
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage information. Optional: Use enclosed instructions for Swag Hook installation.
Install the bottom tier to the top tier by screwing the fixture arms to the swivels and bottom of the top tier. Assemble the top tier by screwing the fixture arms to the ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 1. 2. 3.
F2942-6. Chandelier. F2942/6. Install the candle followers by placing them on top of the ... This product may be dimmed with a standard incandescent dimmer.
Installez les tubes de bougies en les glissant sur les douilles. Installez les suiveurs de la bougie au sommet des tubes de bougies. Vissez l'ampoules dans les ...
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SMALL ORNAMENT. THUMB SCREW. 7. F
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes . Consulte la etiqueta del casquillo de la lámpara para obtener información Max.