CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations. Incandescent lamps may be dimmed with a standard incandescent dimmer. LED lamps may be dimmed with a LED dimmer. Consult lamp manufacturer for additional information.
Use minimum 90°c supply conductors.
1A 5
STEM ASSEMBLY
CAP
SHORT SCREW
2
2
UPPER FRAME
1 WASHER
SOCKET ASSEMBLY
SIDE FRAME
4
LAMP
3
CANDLE FOLLOWER CANDLE TUBE
LOWER FRAME LONG SCREW
2
2
1
Feed the fixture wires through the washer and upper frame, then screw the upper frame onto the socket assembly.
2
Install the lower frame to the side frames using the long screws, then secure the side frames to the upper frame using the short screws. Install the caps over the screws.
3
Install the candle followers to the top of the candle tubes.
4
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
5
Follow enclosed supplement installation instructions for electrical and fixture installation onto junction box.
1
1.0
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c.
1A 5
ENSEMBLE DE TIGE CAPUCHON
VIS COURT
2
2
CADRE SUPÉRIEUR
1 RONDELLE
ENSEMBLE DE DOUILLE
CADRE LATÉRAL
4
AMPOULE
3
SUIVEUR DE BOUGIE TUBE BOUGIE
CADRE INFÉRIEUR VIS LONGUE
2
2
1
Alimentez les fils de luminaire à travers la rondelle et le cadre supérieur, puis visser le cadre supérieur sur l'ensemble de douille.
2
Installez le cadre inférieur sur les cadres latéraux à l'aide des vis longues, puis fixez les cadres latéraux au cadre supérieur à l'aide des vis courtes. Installez les capuchons sur les vis.
3
Installez les tubes de bougies en les glissant sur les douilles.
4
Vissez l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de lampe pour information Max Wattage.
5
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et de montage sur la boîte de jonction.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min.
1A 5
ENSAMBLAJE DE TALLO CAPUCHON
TORNILLO CORTO
2
2
MARCO SUPERIOR
1 ARANDELA
ENSEMBLAJE DEL ENCHUFE
MARCO LATERAL
4
BOMBILLA
3
SEGUIDOR DE VELA TUBO DE VELA
MARCO INFERIOR TORNILLO LARGO
2
2
1
Introduzca los cables de la fijación a través de la arandela y el marco superior, luego atornille el marco superior en el conjunto de enchufe.
2
Instale el bastidor inferior a los marcos laterales con los tornillos largos, luego asegure los marcos laterales al marco superior usando los tornillos cortos. Instale las tapas sobre los tornillos.
3
Instale los tubos vela por el deslizamiento de ellos en los enchufes.
4
Atornille las bombillas en los enchufes. Consulte la etiqueta en el zócalo de la lámpara para obtener información Max Potencia.
5
Siga las instrucciones de instalación del suplemento cerrados para la instalación eléctrica y el accesorio en la caja de conexiones.
3
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077 800.323.3226 - 847.626.6300
Screw the anchor screws into the anchors ensuring one anchor washer and screw secure the safety cable. Connect the ... Connect the white fixture wire (square and/or rigid) to the neutral power line wire with a wire nut. Connect ... VIS COURT.
the fixture screws. Install the silicone pads over the sockets. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
Install the inner and outer rings to each pendant using the thumb screws. ... installation instructions for electrical and fixture installation onto house outlet box. 1.
Follow enclosed supplement installation instructions for electrical and fixture installation onto junction box. Install the threaded pipes by screwing them into ...
additional information. CAUTION RISK OF FIRE. -. This product must be installed in accordance with the applicable installation code by a person familiar with the.
Install the tethered chains by hooking them to the bottom of the fixture, then place the cups onto the threads under the sockets and secure them in place by ...
... the lamp socket for Max Wattage information. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. 1.
Connect the fixture to a suitable ground in accordance to local electrical codes. ... Neatly place all the wires into the junction box, place the canopy onto the ...
installation onto house outlet box. STEM. SEMI-FLUSH MOUNT ... This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Installer un lien rapide sur la boucle de luminaire et la chaîne, puis un autre lien ... Tisser le cordon à travers la chaîne, la dais et hors de la boîte électrique.
instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone. Conductores de alimentacion ...
Determine the height of the fixture with the provided stems and chain/loop, then assemble them by screwing them together. Insert the socket assembly through ...