Install the inner and outer rings to each pendant using the thumb screws. ... installation instructions for electrical and fixture installation onto house outlet box. 1.
Chandelier CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations.
Use minimum 90°c supply conductors.
Incandescent lamps may be dimmed with a standard incandescent dimmer. LED lamps may be dimmed with a LED dimmer. Consult lamp manufacturer for additional information. This instruction shows a typical installation.
1A 4
FIXTURE LOOP
FIXTURE CORD
2 INNER RING
OUTER RING THUMB SCREW
1
1
FIXTURE CORD
PENDANT
OUTER RING INNER RING
PENDANT
3
LAMP
1
Install the inner and outer rings to each pendant using the thumb screws.
2
Feed the fixture wires through the fixture loop and screw it onto the fixture.
3
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage Information.
4
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A 4
CORDE DE LUMINAIRE
2
CORDE DE LUMINAIRE
ANNEAU DE INTERIEUR
ANNEAU DE EXTERIEUR VIS DE POUCE
1
1
BRAS DE LUMINAIRE
PENDANTIF
ANNEAU DE EXTERIEUR ANNEAU DE INTERIEUR
PENDANTIF
3
LAMP
1
Installez les anneaux intérieurs et extérieurs à chaque pendentif en utilisant les vis de serrage.
2
Nourrir les fils de luminaire à travers la boucle de luminaire et visser sur le luminaire.
3
Vissez l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille pour Max Wattage information.
4
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et luminaire sur la boîte de sortie de la maison.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A 4
CORDÓN DE LA LÁMPARA
2
CORDÓN DE LA LÁMPARA
ANILLO DEL INTERIOR
ANILLO DEL EXTERIOR TORNILLO DE PULGAR
1
1
BRAZO DE LA LÁMPARA
COLGANTE
ANILLO DEL EXTERIOR ANILLO DEL INTERIOR
COLGANTE
3
BOMBILLA
1
Instalar los anillos interior y exterior a cada colgante utilizando los tornillos de pulgar.
2
Alimentar a los cables de la lámpara a través del bucle de la lámpara y el atornillelo en la lámpara.
3
Atornille las bombillas en los enchufes. Consulte la etiqueta en la toma de Max Información de Potencia.
4
Siga las instrucciones de instalación del suplemento cerrados para la instalación eléctrica y el accesorio sobre la caja de salida de la casa.
the fixture screws. Install the silicone pads over the sockets. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
Secure the mounting plate to the junction box. Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white fixture wire ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto junction box. Install the threaded pipes by screwing them into ...
additional information. CAUTION RISK OF FIRE. -. This product must be installed in accordance with the applicable installation code by a person familiar with the.
Screw the anchor screws into the anchors ensuring one anchor washer and screw secure the safety cable. Connect the ... Connect the white fixture wire (square and/or rigid) to the neutral power line wire with a wire nut. Connect ... VIS COURT.
Install the tethered chains by hooking them to the bottom of the fixture, then place the cups onto the threads under the sockets and secure them in place by ...
... the lamp socket for Max Wattage information. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. 1.
Connect the fixture to a suitable ground in accordance to local electrical codes. ... Neatly place all the wires into the junction box, place the canopy onto the ...
installation onto house outlet box. STEM. SEMI-FLUSH MOUNT ... This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Installer un lien rapide sur la boucle de luminaire et la chaîne, puis un autre lien ... Tisser le cordon à travers la chaîne, la dais et hors de la boîte électrique.
instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone. Conductores de alimentacion ...
Determine the height of the fixture with the provided stems and chain/loop, then assemble them by screwing them together. Insert the socket assembly through ...