additional information. CAUTION RISK OF FIRE. -. This product must be installed in accordance with the applicable installation code by a person familiar with the.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations. Incandescent lamps may be dimmed with a standard incandescent dimmer. LED lamps may be dimmed with a LED dimmer. Consult lamp manufacturer for additional information.
Use minimum 90°c supply conductors.
1A 6
FIXTURE LOOP
5 4
LAMP
3
CANDLE FOLLOWER
2
CANDLE TUBE
SOCKET
1
1
CAP NUT
LOWER FRAME
1
Install the lower frame to the bottom of the fixture and secure it in place using the cap nuts.
2
Install the candle tubes by slipping them over the sockets.
3
Install the candle followers to the top of the candle tubes.
4
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
5
Feed the fixture wires through the fixture loop and screw it onto the fixture.
6
Follow enclosed supplement installation instructions for electrical and fixture installation onto junction box.
1
1.0
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c.
1A 6
BOUCLE DE LUMINAIRE
5 4
AMPOULE
3
SUIVEUR DE BOUGIE
2
TUBE BOUGIE
DOUILLE
1
1
ECROU CAPUCHON
CADRE INFÉRIEUR
1
Installez le cadre inférieur au bas de luminaire et fixez-le en place à l'aide des écrous capuchon.
2
Installez les tubes de bougies en les glissant sur les douilles.
3
Installez les suiveurs de la bougie au sommet des tubes de bougies.
4
Vissez l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de lampe pour information Max Wattage.
5
Alimentez les fils de luminaire à travers la boucle de luminaire et vissez-le sur le luminaire.
6
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et de montage sur la boîte de jonction.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min.
1A 6
BUCLE DE LA LÁMPARA
5 4
BOMBILLA
3
SEGUIDOR DE VELA
2
TUBO DE VELA
ENCHUFE
1
1
TUERCA CAPUCHON
MARCO INFERIOR
1
Instale el bastidor inferior en la parte inferior del accesorio y asegúrelo en su lugar usando las tuercas de tapa.
2
Instale los tubos vela por el deslizamiento de ellos en los enchufes.
3
Instale los seguidores de la vela a la parte superior de los tubos de la vela.
4
Atornille las bombillas en los enchufes. Consulte la etiqueta en el zócalo de la lámpara para obtener información Max Potencia.
5
Alimente los cables del aparato a través del anillo de fijación y atorníllelo en el aparato.
6
Siga las instrucciones de instalación del suplemento cerrados para la instalación eléctrica y el accesorio en la caja de conexiones.
3
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077 800.323.3226 - 847.626.6300
the fixture screws. Install the silicone pads over the sockets. Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
Install the inner and outer rings to each pendant using the thumb screws. ... installation instructions for electrical and fixture installation onto house outlet box. 1.
Follow enclosed supplement installation instructions for electrical and fixture installation onto junction box. Install the threaded pipes by screwing them into ...
Screw the anchor screws into the anchors ensuring one anchor washer and screw secure the safety cable. Connect the ... Connect the white fixture wire (square and/or rigid) to the neutral power line wire with a wire nut. Connect ... VIS COURT.
Install the tethered chains by hooking them to the bottom of the fixture, then place the cups onto the threads under the sockets and secure them in place by ...
... the lamp socket for Max Wattage information. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. 1.
Connect the fixture to a suitable ground in accordance to local electrical codes. ... Neatly place all the wires into the junction box, place the canopy onto the ...
installation onto house outlet box. STEM. SEMI-FLUSH MOUNT ... This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Installer un lien rapide sur la boucle de luminaire et la chaîne, puis un autre lien ... Tisser le cordon à travers la chaîne, la dais et hors de la boîte électrique.
instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone. Conductores de alimentacion ...
Determine the height of the fixture with the provided stems and chain/loop, then assemble them by screwing them together. Insert the socket assembly through ...
código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de ...