Determine the height of the fixture with the provided stems and assemble them by screwing them together. Secure the mounting plate to the junction box with two ...
Pendant GENERAL PRODUCT INFORMATION: This product is listed by one of the following “Nationally Recognized Testing Laboratory” These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is suitable for dry locations only.
Use minimum 90°c supply conductors.
This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
1A MOUNTING PLATE FIXTURE SCREW
10 10
6 CANOPY
3 STEM
3
5
SOCKET ASSEMBLY
SHADE
1
SHADE RING COLLAR NUT LAMP
2 1 2 3 4 5 6 7 8 9 10
If necessary, place the shade ring onto the shade so that it rests as shown, then place the shade onto the socket and secure it in place by screwing the collar nut onto the socket. Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. Determine the height of the fixture with the provided stems and assemble them by screwing them together. Secure the mounting plate to the junction box with two mounting plate screws. Feed the fixture wires through the stem assembly and screw the stem assembly to the socket assembly. Feed the fixture wires through the canopy and screw the canopy onto the stem assembly. Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut. Connect the black fixture wire to the hot power line wire with a wire nut. Neatly place the wires into the electrical box and/or canopy, then place the canopy onto the mounting plate and secure it in place by screwing in the fixture screws.
1
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c. 1A PLAQUE DE MONTAGE VIS DE LUMINAIRE
10 10
6 DAIS
3 TIGE
3
5
ENSEMBLE DE DOUILLE
ABAT-JOUR
1
ANNEAU DE ABAT-JOUR ECROU DE COLLIER AMPOULE
2
1 2 3 4 5 6 7 8 9 10
Si nécessaire, placer la anneau de l'abat-jour sur l'abat-jour de sorte qu'il repose comme indiqué, puis placez l'abat-jour sur le douille et le fixer en vissant l’écrou de collier sur la douille. Visser l’ampoule dans la douille. Reportez-vous à l'étiquette sur la douille de lampe pour obtenir des informations Max Puissance. Déterminer la hauteur de luminaire avec le fourni tiges et les assembler en les vissant ensemble. Fixer la plaque de montage sur le boîte de jonction avec deux vis de montage. Faire passer les fils de luminaire à travers les tiges et visser l'ensemble de la tige pour le luminaire. Faire passer les fils de luminaire à travers la dais et visser le dais sur l'esemble de tige. Connectez le luminaire à un terrain approprié conformément aux codes électriques locaux. Connectez le fil blanc de luminaire au fil ligne neutre avec un capuchon de connexion. Connectez le fil noir de luminaire au fil ligne chaude avec un capuchon de connexion. Parfaitement placer les fils dans le boîte de jonction et/ou de la dais, puis déposer la dais sur la plaque de montage et fixezle en serrant les vis de luminaire.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min. 1A PLACA DE MONTAJE TORNILLO DE LA LÁMPARA
10 10
6 DOSEL
3 TALLO
3
5
ASAMBLEA DE ENCHUFE
PANTALLA
1
ANILLO DE LA PANTALLA TUERCA DE COLLAR BOMBILLA
2
1 2 3 4 5 6 7 8 9 10
Si es necesario, coloque el anillo de la pantalla sobre la pantalla para que se apoye como se muestra, y luego coloque la pantalla en el enchufe y fijarla en su lugar enroscando la tuerca de collar en el enchufe. Atornille la bombilla en el enchufe. Consulte la etiqueta del enchufe para obtener información Max Potencia. Determinar la altura de la lámpara con el proporcionado tallos y ensamblarlos mediante atornillado juntos. Fije la placa de montaje a la caja eléctrica con dos tornillos de la placa de montaje. Pasar los cables de la lámpara a través de los tallos y atornille el tallo para la lámpara. Pasar los cables de la lámpara a través de el dosel y atornille el dosel en el ensamble de la tallo. Conecte la lámpara a una tierra apropiada de acuerdo a los códigos eléctricos locales. Conecte el cable blanco de la lámpara al cable neutro línea con una tuerca para hilos. Conecte el cable negro de la lámpara al cable de línea caliente potencia con una tuerca de alambre. Cuidadosamente coloque los cables en la caja eléctrica o dosel, luego colocar el dosel en la placa de montaje y asegúrelo en su lugar apretando los tornillos de la lámpara.
Installation Instructions for ... Feed the fixture wires through the stem assembly and screw the stem ... box, place the canopy onto the mounting plate, and secure it in place with the ... Refer to the label on the lamp socket for Max Wattage informa
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SHADE. T
Refer to the label on the lamp socket for Max Wattage information. Follow enclosed supplement installation instructions for electrical and fixture installation onto ...
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes. Instalar los seguidores de la vela por su inclusión en la parte superior de los tubos de ...
applicable installation code by a person familiar with the ... Ce produit doit être installé selon le code d'installation pertinent , ... A Generation Brands Company.
Connect the fixture to a suitable ground in accordance to local electrical codes. ... Neatly place all the wires into the junction box, place the canopy onto the ...
código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de ...
Colorado Springs 1 Light Pendant. 1.2. P1390. Pendant. P1390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant. NEC junction boxes. This product is safety listed for damp locations. This product may
From the end of the cord, strip the insulation 4â and then strip the end of the ... with the construction and operation of the product ... A Generation Brands Company.
Secure the mounting plate to the electrical box with two mounting plate screws. Feed the fixture wires through the canopy and screw the canopy onto the stem assembly. Connect the fixture to a suitable ground in accordance to local electrical codes. C
Screw a nut onto one end of the threaded pipe, then place the shade and a washer over the other end of the threaded pipe and secure them together by ...
P1415. Place the shade onto the socket and secure it in place by screwing the collar nut onto the socket using the shade tool. ... A Generation Brands Company.
Secure the mounting plate to the electrical box with two mounting plate screws. ... Connect the black fixture wire (round and/or smooth) to the hot power line wire ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
Botanic 1 Light Mini-Pendant. Reach inside the shade and screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
Caprice 1 Light Mini-Pendant. 1.1. P1299. Pendant. P1299. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may