Screw a nut onto one end of the threaded pipe, then place the shade and a washer over the other end of the threaded pipe and secure them together by ...
Pendant GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for dry locations only.
1A 5
SOCKET ASSEMBLY THUMB SCREW
3
2
NUT
LAMP
WASHER
SHADE
3
THREADED PIPE
1 WASHER
NUT DECORATIVE CUP
4 FINIAL 1
Screw a nut onto one end of the threaded pipe, then place the shade and a washer over the other end of the threaded pipe and secure them together by tightening with the other nut.
2
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
3
Install the shade to the socket assembly and secure it in place by using the thumb screws.
4
Place the decorative cup over the threaded pipe and secure them in place by tightening the finial.
5
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A 5
ASSEMBLÉE DE DOUILLE VIS DE POUCE
3
2
ECROU
AMPOULE
RONDELLE
ABAT-JOUR
3
TUYAU FILETÉ
1 RONDELLE
ECROU COUPE DÉCORATIF
4 FLEURON 1
Vissez un écrou sur une extrémité de la tige filetée, puis placez l'ombre et une rondelle sur l'autre extrémité de la tige filetée et fixez-les ensemble en serrant avec l'autre noix.
2
Vissez l'ampoule dans la douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
3
Installer l'abat-jour à la assemblée de douille et fixez-le à l'aide des vis de pouce.
4
Placer le coupe décoratif sur le tuyau fileté et fixez-les en place en serrant le fleuron.
5
Suivez supplément ci-joint des instructions électriques et installation d'accessoires dans la boîte de prise de maison.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A 5
ASAMBLEA DE ENCHUFE TORNILLO DE PULGAR
3
2
TUERCA
BOMBILLA
ARANDELA
PANTALLA
3
TUBO ROSCADO
1 ARANDELA
TUERCA COPA DECORATIVA
4 FINIAL 1
Enrosque una tuerca en un extremo de el tubo roscado, luego coloque la pantalla y una arandela sobre el otro extremo del tubo roscado y fíjelos juntos apretando con la otra tuerca.
2
Enrosque la bombilla en el enchufe. Consulte la etiqueta en el zócalo de la lámpara para obtener información de Max Wattage.
3
Instalar la pantalla a la asamblea de enchufe y asegúrelo en su lugar utilizando los tornillos de pulgar.
4
Coloque la copa decorativa sobre el tubo roscado y fíjelos en su lugar apretando el finial.
5
Siga las instrucciones de Instalación incluido suplemento para eléctricos e instalación del accesorio en la caja de enchufe de casa.
From the end of the cord, strip the insulation 4â and then strip the end of the ... with the construction and operation of the product ... A Generation Brands Company.
Secure the mounting plate to the electrical box with two mounting plate screws. ... Connect the black fixture wire (round and/or smooth) to the hot power line wire ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
Trim the cord leaving enough to make electrical connections. Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. FIXTURE.
Determine the wanted height of the fixture by feeding the cord through the canopy and moving the cord up or down. Place the cord in between the two cord clips ...
the applicable installation code by a person familiar with the construction and operation ... código de instalación aplicable por una persona familiarizada con la ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto junction box. Screw the lamps into ... A Generation Brands Company.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 3. SOCKE
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SHADE. T
sujeción en caja de salida de casa. Instale la lámpara enroscándolo en la toma de corriente. Consulte la etiqueta del casquillo de la lámpara para obtener.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamps into the sockets. Refer to the ...
Connecter le fil blanc du luminaire (carré et / ou rigide) pour le fil de ligne à neutre ... Parfaitement placer tous les fils dans la boîte électrique, le montage d'essai ...
Refer to the label on the lamp socket for Max Wattage information. Follow enclosed supplement installation instructions for electrical and fixture installation onto ...
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes. Instalar los seguidores de la vela por su inclusión en la parte superior de los tubos de ...
applicable installation code by a person familiar with the ... Ce produit doit être installé selon le code d'installation pertinent , ... A Generation Brands Company.