Pendant GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for dry locations only.
1A CORD CLIP
4 2 CLIP SCREW
CANOPY
CORD
SOCKET ASSEMBLY
5 SHADE
SPACER COLLAR NUT
LAMP
6
1
Determine the wanted height of the fixture by feeding the cord through the canopy and moving the cord up or down.
2
Place the cord in between the two cord clips and secure it in place using the clip screws.
3
Trim the cord leaving enough for electrical connections. From the end of the cord, strip the insulation 4” and then strip the end of the wires. Note: Make sure not to nick the inner wires.
4
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
5
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut.
6
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. 1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A PINCE DE LE CORDON
4 2 VIS DE LA PINCE
DAIS
CORDON
ASSEMBLÉE DE LE DOUILLE
5 ABAT-JOUR
ESPACEUR ECROU À COLLIER AMPOULE
6
1
Déterminer la hauteur voulue de le luminaire en insérant le cordon à travers le dais et en déplaçant la corde vers le haut ou vers le bas.
2
Placez le cordon entre les deux pince de cordon et fixez-le à l'aide des vis de la pince.
3
Coupez le cordon laissant assez pour le branchement électrique. Dès la fin du cordon, la dénuder 4 "et puis Dénudez l'extrémité des fils. Remarque : Veillez à ne pas nick les fils internes.
4
Reportez-vous aux instructions pour supplément clos électrique et installation de luminaire sur boîte de sortie de maison
5
Placez l'abat-jour et espaceur dans le douille et fixer en place pour serrant l'écrou à collier.
6
Vissez le ampoule dans le douille. Reportez-vous à l'étiquette sur la douille de lampe Puissance max pour plus d'informations.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A PINZA DEL CABLE
4 2 TORNILLO DE LA PINZA
DOSEL
CABLE
ASAMBLEA DE ENCHUFE
5 PANTALLA
ESPACIADOR TUERCA DE COLLAR BOMBILLA
6
1
Determine la altura deseada de la lámpara alimentando el cable a través del dosel y moviendo el cable hacia arriba o hacia abajo.
2
Coloque el cable entre los dos pinzas y asegúrelo en su lugar utilizando los tornillos de la pinza.
3
Recortar el cable dejando suficiente para las conexiones eléctricas. Desde el extremo del cable, pelar el aislamiento de 4 "y luego el extremo de los hilos. Nota: Asegúrese de que no a nick los alambres internos.
4
Siga las instrucciones de Instalación incluido suplemento para eléctricos e instalación del accesorio en la caja de enchufe de casa.
5
Coloque la pantalla y el espaciador, luego asegúrelos apretando la tuerca de collar.
6
Enrosque la bombilla en el enchufe. Consulte la etiqueta en el enchufe de la lámpara para obtener información de Max Wattage.
From the end of the cord, strip the insulation 4â and then strip the end of the ... with the construction and operation of the product ... A Generation Brands Company.
Secure the mounting plate to the electrical box with two mounting plate screws. ... Connect the black fixture wire (round and/or smooth) to the hot power line wire ...
Screw a nut onto one end of the threaded pipe, then place the shade and a washer over the other end of the threaded pipe and secure them together by ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
Trim the cord leaving enough to make electrical connections. Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. FIXTURE.
Determine the wanted height of the fixture by feeding the cord through the canopy and moving the cord up or down. Place the cord in between the two cord clips ...
the applicable installation code by a person familiar with the construction and operation ... código de instalación aplicable por una persona familiarizada con la ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto junction box. Screw the lamps into ... A Generation Brands Company.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 3. SOCKE
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SHADE. T
... the lamp socket for Max Wattage information. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. 1.
sujeción en caja de salida de casa. Instale la lámpara enroscándolo en la toma de corriente. Consulte la etiqueta del casquillo de la lámpara para obtener.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamps into the sockets. Refer to the ...
Connecter le fil blanc du luminaire (carré et / ou rigide) pour le fil de ligne à neutre ... Parfaitement placer tous les fils dans la boîte électrique, le montage d'essai ...
Refer to the label on the lamp socket for Max Wattage information. Follow enclosed supplement installation instructions for electrical and fixture installation onto ...
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes. Instalar los seguidores de la vela por su inclusión en la parte superior de los tubos de ...