Secure the mounting plate to the electrical box with two mounting plate screws. Feed the fixture wires through the canopy and screw the canopy onto the stem assembly. Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white fixture wire (square and/or rigid) to the neutral power ...
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only.
Use minimum 90°c supply conductors. This instruction shows a typical installation.
1A
10
CANOPY
1
MOUNTING PLATE
9
THUMB SCREW
2 FIXTURE SCREW
SHADE COVER
3
11
11
7
SOCKET ASSEMBLY
1 3
STEM
1 THREADED PIPE
1 CHAIN/LOOP
1
FINIAL
DIFFUSER
5
SHADE
FINIAL 1
Determine the height of the fixture with the provided stems and chain/loop, then assemble them by screwing them together.
2
Place the shade cover on the top of the shade and secure it in place using the thumb screws.
3
Insert the socket assembly through the shade and shade cover, then screw the stem onto the socket assembly.
4
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
5
Place the diffuser onto the threaded pipe and secure it in place by screwing on the finial of your choice.
6
Secure the mounting plate to the electrical box with two mounting plate screws.
7
Feed the fixture wires through the canopy and screw the canopy onto the stem assembly.
8
Connect the fixture to a suitable ground in accordance to local electrical codes.
9
Connect the white fixture wire (square and/or rigid) to the neutral power line wire with a wire nut.
10
Connect the black fixture wire (round and/or smooth) to the hot power line wire with a wire nut.
11
Neatly place all the wires into the electrical box, place the canopy onto the mounting plate, and secure it in place by screwing in the fixture screws.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
10
DAIS
1
PLAQUE DE MONTAGE
9
THUMB SCREW
2 VIS DE LUMINAIRE
3
11
11
COUVERCLE D’ABAT-JOUR
7
ASSEMBLAGE DE DOUILLE
1 3
TIGE
1 TUYAU FILETÉ
1 CHAÎNE/BOUCLE
1
DIFFUSEUR
FLEURON
5
ABAT-JOUR
FLEURON 1
Déterminer la hauteur de le luminaire avec les tiges fournies et de la chaîne/boucle, puis les assembler en les vissant ensemble.
2
Placer le couvercle de l'abat-jour sur le dessus de l'abat-jour et fixez-le à l'aide des vis de pouce.
3
Insérer la assemblage de douille à travers l'abat-jour et couvercle d’abat-jour, puis vissez la tige sur la douille.
4
Placer le diffuseur sur la tige fileté et fixer en place en vissant le fleuron de votre choix sur le tuyau filete.
5
Fixer la plaque de montage sur le boîte électrique avec deux vis de montage.
6
Faire passer les fils du luminaire à travers la dais et visser le dais sur l'assembleé de la tige.
7
Connectez le luminaire à un terrain approprié conformément aux codes électriques locaux.
8
Connectez le fil blanc de le luminaire (carré et/ou rigide) au fil ligne neutre avec un capuchon de connexion.
9
Connectez le fil noir de le luminaire (rond et/ou lisse) au fil ligne chaude avec un capuchon de connexion.
10
Parfaitement placer tous les fils dans la boîte électrique, placez la dais sur la plaque de montage et fixer en place en serrant les vis de luminaire.
11
Vissez l'ampoule dans la douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
10
DOSEL
1
PLACA DE MONTAJE
9
TORNILLO DE PULGAR
2 TORNILLO DE LA LÁMPARA
3
11
11
CUBIERTA DE LA PANTALLA
7
ASAMBLEA DE ENCHUFE
1 3
TALLO
1 TUBO ROSCADO
1 CADENA/BUCLE
1
FINIAL
DIFUSOR
5
PANTALLA
FINIAL 1
Determinar la altura de la lámpara con los tallos proporcionados y cadena/lazo, luego ensamblarlos atornillándolos juntos.
2
Coloque la cubierta de la pantalla en la parte superior de la pantalla y asegúrelo en su lugar utilizando los tornillos de pulgar.
3
Inserte el asamblea de enchufe a través de la pantalla y cubierta de la pantalla, luego enrosque la asamblea de enchufe.
4
Coloque el difusor en el tubo roscado y fijarlo en su lugar atornillando el finial de su elección en el tubo roscado.
5
Fije la placa de montaje a la caja eléctrica con dos tornillos de montaje.
6
Pasar los cables de la lámpara a través del dosel y atornille el dosel en la asamblea de tallo.
7
Conecte la lámpara a una tierra apropiada de acuerdo a los códigos eléctricos locales.
8
Conecte el cable blanco de la lámpara (cuadrado o rígido) para el cable neutro línea con una tuerca para hilos.
9
Conecte el cable negro de la lámpara (redondo o liso) para el cable de línea de energía caliente con una tuerca de alambre.
10
Cuidadosamente Coloque todos los cables en la caja eléctrica, coloque el dosel en la placa de montaje y asegúrelo en su lugar atornillando los tornillos de la lámpara.
11
Enrosque la bombilla en el enchufe. Consulte la etiqueta en el zócalo de la lámpara para obtener información de Max Wattage.
Determine the height of the fixture with the provided stems and chain/loop, then assemble them by screwing them together. Insert the socket assembly through ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SHADE. T
Installer un lien rapide sur la boucle de luminaire et la chaîne, puis un autre lien ... Tisser le cordon à travers la chaîne, la dais et hors de la boîte électrique.
Refer to the label on the lamp socket for Max Wattage information. Follow enclosed supplement installation instructions for electrical and fixture installation onto ...
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes. Instalar los seguidores de la vela por su inclusión en la parte superior de los tubos de ...
Marteau 1 Light Wall. 1.0. W 1782. B. W 1782. B. Wall. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
applicable installation code by a person familiar with the ... Ce produit doit être installé selon le code d'installation pertinent , ... A Generation Brands Company.
These fixtures are intended to be installed utilizing compliant junction. NEC boxes. This product is safety listed for damp locations. Incandescent lamps may be ...
Screw a nut onto one end of the threaded pipe, then place the shade and a washer over the other end of the threaded pipe and secure them together by ...
CABLE NEGRO. CAJA ELÉCTRICA. PLACA DE. MONTAJE. LÁMPARA. PRECAUCIÓN: RIESGO DE INCENDIO. Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los
Colorado Springs 1 Light Pendant. 1.2. P1390. Pendant. P1390. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant. NEC junction boxes. This product is safety listed for damp locations. This product may
sujeción en caja de salida de casa. Instale la lámpara enroscándolo en la toma de corriente. Consulte la etiqueta del casquillo de la lámpara para obtener.
From the end of the cord, strip the insulation 4â and then strip the end of the ... with the construction and operation of the product ... A Generation Brands Company.
Connect the black fixture wire to the hot power line wire with a wire nut. Secure the fixture to the post with the post screws making sure to neatly tuck in all wiring.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamps into the sockets. Refer to the ...
P1415. Place the shade onto the socket and secure it in place by screwing the collar nut onto the socket using the shade tool. ... A Generation Brands Company.