Low Noise, Cascadable Silicon Bipolar MMIC Amplifier ... - OM 3 BC
The INA series of MMICs is fabricated using HP's 10 GHz fT,. 25 GHz fMAX, ISOSATâ¢-I silicon bipolar process which uses nitride self-alignment, submicrometer.
Low Noise, Cascadable Silicon Bipolar MMIC Amplifier Technical Data INA-10386
Features • Cascadable 50 Ω Gain Block • 3 dB Bandwidth: DC to 1.8 GHz • 26 dB Typical Gain at 1.5␣ GHz • 10 dBm Typical P1dB at 1.5␣ GHz • Unconditionally Stable (k>1) • Surface Mount Plastic Package
Description The INA-10386 is a low-noise silicon bipolar Monolithic Microwave Integrated Circuit (MMIC)
feedback amplifier housed in a low cost surface mount plastic package. It is designed for narrow or wide bandwidth commercial and industrial applications that require high gain and moderate power. The INA series of MMICs is fabricated using HP’s 10 GHz fT, 25␣ GHz fMAX, ISOSAT™-I silicon bipolar process which uses nitride self-alignment, submicrometer lithography, trench isolation, ion implantation, gold metallization and polyimide intermetal dielectric and scratch protection to achieve excellent performance, uniformity and reliability.
Typical Biasing Configuration VCC Id = 45 mA nom.
RFC (Optional) Rbias
4
Cblock RF IN
Cblock 3
1 2
RF OUT Vd = 6.0 V
86 Plastic Package
2
INA-10386 Absolute Maximum Ratings Absolute Maximum[1]
Parameter Device Current Power Dissipation[2,3] RF Input Power Junction Temperature Storage Temperature
80 mA 750 mW +13 dBm 150°C –65 to 150°C
Thermal Resistance: θjc = 100°C/W Notes: 1. Permanent damage may occur if any of these limits are exceeded. 2. TCASE = 25°C. 3. Derate at 10 mW/°C for TC > 75°C.
INA-10386 Electrical Specifications[1], TA = 25°C Symbol
Parameters and Test Conditions: Vd = 6V, ZO = 50 Ω
GP
Power Gain (|S21| 2)
f = 1.5 GHz
∆GP
Gain Flatness
f = 0.1 to 1.5 GHz
f3 dB
3 dB Bandwidth[2]
ISO VSWR
Reverse Isolation (|S12
| 2)
f = 2.0 GHz
Input VSWR
Units
Min.
Typ.
dB
23.0
26.0
dB
±1.0
GHz
1.8
dB
Max.
30
f = 0.1 to 2.0 GHz
1.5:1
Output VSWR
f = 0.1 to 2.0 GHz
NF
50 Ω Noise Figure
f = 1.5 GHz
1.5:1
P1 dB
Output Power at 1 dB Gain Compression
f = 1.5 GHz
dBm
10
IP3
Third Order Intercept Point
f = 1.5 GHz
dBm
23
tD
Group Delay
f = 1.5 GHz
psec
Id
Device Current
dV/dT
Device Voltage Temperature Coefficient
dB
mA mV/°C
3.8
250 35
45
55
+10
Notes: 1. The recommended operating current range for this device is 40 to 60 mA. Typical performance as a function of current is on the following page.
INA-10386 Part Number Ordering Information Part Number
Low Cost Plastic Package. MSA-0885 ... Output Power at 1 dB Gain Compression f = 1.0 GHz. dBm. 12.5. IP3. Third Order Intercept Point f = 1.0 GHz. dBm. 27.0.
Hewlett-Packard's MGA-86576 is an economical, easy-to-use GaAs. MMIC amplifier that offers low noise and excellent gain for applications from 1.5 to 8 GHz.
The MC54/74HC86 is identical in pinout to the LS86; this device is similar in function ..... M. N. 0.785. 0.280. 0.200. 0.020. 0.065. 0.015. 0.170. 15°. 0.040. 0.750.
at TA = 25 °C, unless otherwise specified. Parameter. Symbol. Value. Unit min. typ. max. DC Characteristics. Collector-emitter breakdown voltage. IC = 1 mA.
Jul 12, 1999 - 16 Bit Shift Register ... OSCOUT. 1. 2. Data 10. Clock 9. LE 11. fIN 8 f r. 13. FC. 12. ÏR. 16. DO. 5. ÏP ... the phase difference of fr and fp exits. 8.
Figure 1. Figure 2. 3 V. GND tf tr. INPUT. A OR B. OUTPUT. YA OR YB. 0.3 V ... 2.54 BSC. 0.100 BSC. H. 0.51. 1.27. 0.020. 0.050. J. 0.20. 0.30. 0.008. 0.012. K.
OperationalAmplifier. February 1995. LM837 Low Noise Quad Operational Amplifier. General Description. The LM837 is a quad operational amplifier designed ...
This device consists of two independent 2âbit transparent latches. Each latch stores the input data while Latch Enable is at a logic low. The outputs follow the ...
frequency prescaler, phase/frequency detector, charge pump, and reference oscillator/buffer .... differential pair. The nonâinverting input of the differential pair.
ECG and noninvasive blood pressure monitors. ..... human body and on test equipment, can discharge without de- ..... invasive blood pressure measurement.
Proper safeguards, such as isolation, must be added to .... Transformer Coupled Inputs sources such as transformers, or ac-coupled sources, there must be a dc ...
Texas Instru- ments recommends that all integrated circuits be handled with ... changes could cause the device not to meet its published specifications. NC. RG2.
A patented, on-chip active bias circuit allows operation from a single +5 V power supply. Current consumption is only 16 mA. These devices are 100% RF tested ...
Introduction. The Hewlett-Packard ATF-36077. PHEMT device is described in a low noise amplifier for 2.3 GHz. The ATF-36077 is characterized for use as a low ...