44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax (516) 515.5050. Western Distribution Center. 1750 Archibald Ave • Ontario, CA ...
INSTALLATION INSTRUCTION HR90 LED Undercabinet Button Lights HR-LED90 WARNING IMPORTANT: NEVER attempt to do any work without shutting off the electricity. 1. Read all instructions before installing. 2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. 3. Place the wall switch in the “OFF” position. 4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the space that you are working on. CAUTION - All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction may invalidate the ETL/cETL listing of this fixture. AVERTISSEMENT IMPORTANT : Coupez l’électricité avant TOUTE manipulation. - Lisez toutes les instructions avant d’installer. - Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. - Placez l’interrupteur mural en position d’arrêt (« OFF »). - Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus MISE EN GARDE - Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/cETL du luminaire.
INSTALLATION A) Recessed Mounting NOTE: The back plate is not needed for recessed mounting and may be discarded.
Output 24V
Transformer
Input 120V
Back Plate Cover Piece
1. 2. 3. 4.
Cut a 3 1/4” diameter hole in the surface. Feed the fixture wires through the hole, and connect the wires to a 24V transformer. Compress the springs on either side of the cover piece and insert it into the opening. Fit the light fixture into the cover piece. Light fixture is held in place by magnet.
Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050
Light Fixture
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. December, 2014
1
INSTALLATION INSTRUCTION HR90 LED Undercabinet Button Lights HR-LED90 B) Surface Mounting NOTE: The cover piece is not needed for surface mounting and may be discarded.
Leveling the screw
Cover Piece Back Plate
1. Wires may be run behind the fixture or along the mounting surface. Determine the most convenient location for wire passage. 2. Screw the back plate to the surface with screws provided. Ensure that the screw’s heads level with back plate. 3. To wire behind the fixture, drill a hole in the surface sufficient to allow the socket wires through. 4. Feed the fixture wires through the hole, and connect the wires to a 24V transformer. 5. Snap the light fixture onto back plate. Light fixture is held in place by magnet.
Wires behind the fixture Output 24V
Transformer
Input 120V
Back Plate
Light Fixture
WIRING Installation within a cabinet require 24V Class 2 transformers. Class 2 transformers are by definition “Power limited” (5 amps maximum) and “Inherently Protected” (fused). Primary wires to the transformer enclosure must follow normal NEC Chapter 3 wiring techniques. Non-enclosed secondary wiring and splices are not restricted in concealed spaces.
Wires along the mounting surface
Light Fixture Output 24V
Transformer
Input 120V
TRANSFORMERS: Use to power the HR-90 button light. Below is a list of compatible transformer models and descriptions (sold separately) Model Number
Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. December, 2014
A) Recessed Mounting. NOTE: The back plate is not needed for recessed mounting and may be discarded. 1. Cut a 3 1/4â diameter hole in the surface. 2. Feed the fixture wires through the hole, and connect the wires to a 24V transformer. 3. Compress t
... of our products at any time as part of the company's continuous improvement .... power-up the fixture in order to allow the 0-10V dimming to function properly.
www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
44 Harbor Park Drive. Port Washington, NY ... Wire Connector. Qty: 3 pcs ... Connect the driver input/output wire to junction box wires as shown in Fig. 2, making ...
Insert the open end of the rail adapter into the rail and make sure that the contact points sit into the grooves of the rail. 4. Place the cap ring back onto the rail ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax ... August, 2014 ... System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. -. Place the ...
June, 2014 ... Secure mounting backplate (D1) to the junction box (F1) ... White. (Neutral). House Wires. Green or Bare Copper. (Ground). F1. A1. D1. B1. C1. G1.
44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs, GA 30122. Western Distribution Center.
the circuit breaker switch(es) that control the power to the fixture or room that you are ... CAUTION When handling the fixture, do not apply pressure to the LEDs.
Note: Actual depth of box to be determined in accordance with the NEC and local ordinances. Indoor or outdoor frame mounted junction box: Raco 2” x4” (16.5 ...
Port Washington, NY 11050. Central Distribution ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker ...
Connect black fixture wire to hot wire, white fixture wire to neutral wire and green fixture wire to ground (as Fig.2). 5. Place all wiring and connectors back in ...
DeCember, 2014. 1 ... 4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to ...
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous ... Coloque el interruptor de ali mentación.
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
Headquarters/Eastern Distribution Center. 44 Harbor ... Western Distribution Center ... White or. Ribbed. Fixture Wires. Bare wire. (Ground). House Wires. Black.
(ie moisture-proof polyurethane). Important! Ensure you do not cut through the toekick below. Important! Ensure you do not cut through the toekick below.
Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs, GA 30122. Western Distribution Center. 1750 Archibald Avenue.
CAUTION. - All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken.
IMPORTANT: NEVER attempt any work without shutting off the electricity. -. Read all instructions before installing. -. System is intended for installation by a ...
Do not substitute any parts, leave parts out, or use any parts that are ... of our products at any time as part of the company's continuous improvement program.