DeCember, 2014. 1 ... 4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to ...
INSTALLATION INSTRUCTION LINE™ 2.0 LED With Remote Transformer LN-LED06P/LED12P/LED18P/LED24P/LED30P WARNING IMPORTANT: NEVER attempt to do any work without shutting off the electricity. 1. Read all instructions before installing. 2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. 3. Place the wall switch in the “OFF” position. 4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the space that you are working on. CAUTION - All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction may invalidate the ETL/cETL listing of this fixture. AVERTISSEMENT IMPORTANT : Coupez l’électricité avant TOUTE manipulation. - Lisez toutes les instructions avant d’installer. - Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. - Placez l’interrupteur mural en position d’arrêt (« OFF »). - Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus MISE EN GARDE - Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/cETL du luminaire. INSTALLATION: 1. Choose the desired mounting position for the LINE™ fixture, recommended either at the back or front of the cabinet. 2. Use a proper tool to separate the mounting plate from the LINE™ light panel.
4 Pieces
4 Pieces T20
3. Fasten the mounting plate to surface using the provided mounting screws. 4. Fold up the LINE™ light panel until the integrated magnets snap to the mounting plate.
Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. December, 2014
1
INSTALLATION INSTRUCTION LINE™ 2.0 LED With Remote Transformer LN-LED06P/LED12P/LED18P/LED24P/LED30P WIRING: Connecting a Single Fixture: Insert the plug at the end of transformer cord into either socket on the LINE™ fixture. Interconnecting Fixtures with Jumper Wires: Insert the end plug of the jumper wires into each LINE™ fixture socket. See accessories below for different lengths and configurations of jumper wires.
Socket Plug
Remote Transformer
TRANSFORMERS/ACCESSORIES: NOTE: All transformers and accessories are sold separately. TRANSFORMERS: Use to power the LINE™ fixtures. Below is a list of compatible transformer models and descriptions Model Number
Description
EN-2460-P-AR-S
60W plug-in transformer, 120V AC
EN-24100-P-AR-S
96W plug-in transformer, 120V AC
EN-2460-RB2-S
60W remote transformer, 120V AC
EN-24100-RB2-S
96W remote transformer, 120V AC
The maximum number of LINE™ fixtures that can be interconnected together is shown on the chart below. Model Number
Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. December, 2014
2
INSTALLATION INSTRUCTION LINE™ 2.0 LED With Remote Transformer LN-LED06P/LED12P/LED18P/LED24P/LED30P JUMPER WIRES: Use to link multiple LINE™ fixtures through surface wiring. They are available in following length and configurations: Model Number
Description
SL-IC-06
6 inch jumper wire
SL-IC-12
12 inch jumper wire
SL-IC-24
24 inch jumper wire
SL-IC-36
36 inch jumper wire
SL-EXT-144
12 ft. jumper wire
SL-Y
Y connector
SL-X
X connector
SL-IF
Female jumper wire connector
TERMINAL BLOCKS: Use to connect up to 8 LINE™ fixtures independently. Model Number
Description
MTB-08
Connects up to 8 fixtures
WIRING BOX WITH SWITCH: Use when spanning a large gap in a system layout without leaving exposed wiring. Model Number
Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. December, 2014
... of our products at any time as part of the company's continuous improvement .... power-up the fixture in order to allow the 0-10V dimming to function properly.
www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax (516) 515.5050. Western Distribution Center. 1750 Archibald Ave • Ontario, CA ...
44 Harbor Park Drive. Port Washington, NY ... Wire Connector. Qty: 3 pcs ... Connect the driver input/output wire to junction box wires as shown in Fig. 2, making ...
Insert the open end of the rail adapter into the rail and make sure that the contact points sit into the grooves of the rail. 4. Place the cap ring back onto the rail ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax ... August, 2014 ... System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. -. Place the ...
June, 2014 ... Secure mounting backplate (D1) to the junction box (F1) ... White. (Neutral). House Wires. Green or Bare Copper. (Ground). F1. A1. D1. B1. C1. G1.
44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs, GA 30122. Western Distribution Center.
the circuit breaker switch(es) that control the power to the fixture or room that you are ... CAUTION When handling the fixture, do not apply pressure to the LEDs.
Note: Actual depth of box to be determined in accordance with the NEC and local ordinances. Indoor or outdoor frame mounted junction box: Raco 2” x4” (16.5 ...
Port Washington, NY 11050. Central Distribution ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker ...
Connect black fixture wire to hot wire, white fixture wire to neutral wire and green fixture wire to ground (as Fig.2). 5. Place all wiring and connectors back in ...
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous ... Coloque el interruptor de ali mentación.
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
A) Recessed Mounting. NOTE: The back plate is not needed for recessed mounting and may be discarded. 1. Cut a 3 1/4â diameter hole in the surface. 2. Feed the fixture wires through the hole, and connect the wires to a 24V transformer. 3. Compress t
Headquarters/Eastern Distribution Center. 44 Harbor ... Western Distribution Center ... White or. Ribbed. Fixture Wires. Bare wire. (Ground). House Wires. Black.
Mar 31, 2017 - The Apex Paradox. 4. Nina Haslinger and Viola Schmitt. Stressed non-Boolean und (and) in German. 5. Sara S. Loss. Two types of subordinate ...
(ie moisture-proof polyurethane). Important! Ensure you do not cut through the toekick below. Important! Ensure you do not cut through the toekick below.
Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs, GA 30122. Western Distribution Center. 1750 Archibald Avenue.
CAUTION. - All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken.
IMPORTANT: NEVER attempt any work without shutting off the electricity. -. Read all instructions before installing. -. System is intended for installation by a ...
Do not substitute any parts, leave parts out, or use any parts that are ... of our products at any time as part of the company's continuous improvement program.