(ie moisture-proof polyurethane). Important! Ensure you do not cut through the toekick below. Important! Ensure you do not cut through the toekick below.
Installation instruction DishDrawerTM dishwasher DD24S 7, DD24ST 7, DD36ST 7 Integrated models US CA
Installing external venting kit into framed cabinetry only
For customers with framed cabinetry only The supplied Installation Instructions booklet provided with your product explains how to install the supplied external venting kit in frameless cabinetry only. If you are installing the external venting kit into framed cabinetry, then please refer to this booklet for instructions instead. The instructions in this booklet are a replacement for the securing the vent instructions in the main booklet. After you have fitted the external venting kit using this booklet, please then refer back to your main Installation instructions to complete the installation of your dishwasher.
External Venting kit (1)
Securing Bracket & Screw (1)
590452A
03.12
2
1a INTEGRATED MODELS ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH SAME CABINET Important!
Services can be located either side of dishwasher
Ensure you do not cut through the toekick below
Shelf cutouts max. 3⁄16” (5 mm) VENT HOSE
ø max. 1½” (38 mm)
ø 2 3⁄8” (60 mm)
ø 2 3⁄8” (60 mm) 4” (100 mm)
DRAIN HOSE + INLET HOSE + POWER CORD
8 11⁄16” (220 mm)
Important! Ensure any bare wood on exposed frames is adequately sealed to withstand moisture (ie moisture-proof polyurethane)
1” (25 mm) Frame
1b INTEGRATED MODELS ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH ADJACENT CABINET ø 2 3⁄8” 60mm
Services can be located either side of dishwasher
The ø 2 3⁄8” (60 mm) services hole for the hoses should be enlarged to accomodate the extra venting hose by cutting out some material from the bottom corner.
Important! Ensure you do not cut through the toekick below
Shelf cutouts VENT HOSE + DRAIN HOSE + INLET HOSE
max. 3⁄16” (5 mm)
ø max. 1½” (38 mm)
ø 2 3⁄8” (60 mm) If the services holes are through metal, ensure you fit the supplied Edge Protector around the hole for the power cord.
4” (100 mm)
ø 2 3⁄8”
(60 mm)
POWER CORD
8 11⁄16” (220 mm)
Important! Ensure any bare wood on exposed frames is adequately sealed to withstand moisture (ie moisture-proof polyurethane)
1” (25 mm) Frame
2 UNSCREW TOP COVER FROM
EXTERNAL VENT
3 THE SHADED AREAS HAVE TO BE REMOVED.
FIRST, CUT DOWN FRONT FACE WITH A KNIFE
Important!
19
4 CUT OFF REMAINING PLASTIC FROM
EACH SIDE
Score with Knife
Snap off
Ensure you perform this step on a chopping board or similiar. Do not cut on the countertop or floor.
5 LOOSELY ASSEMBLE THE EXTERNAL VENT TOGETHER.
THE VENT IS NOW MODIFIED AND READY TO INSTALL
3
6 ATTACH THE HOSE TO THE VENT &
POSITION IN CUTOUT
7 SECURE THE EXTERNAL VENT USING
BRACKET & SCREWS
Important!
Ensure that the venting hose was attached to the fitted elbow at the back of the product (as per main Installation instructions).
2
1 After routing the vent hose through and out the hole cutout, attach and secure the vent.
Air flo
w
Insert bracket into vent slot and secure to shelf with screw
Screw vent together with the 4 screws
4
5
Instructions d’installation Lave-vaisselle DishDrawerTM Modèles Encastrés DD24S 7, DD24ST 7 et DD36ST 7 US CA (FR)
Installation kit de ventilation externe dans les armoires encadrée seulement
Pour les clients ayant armoires encadrée seulement L’installation fourni manuel d’instructions fourni avec votre produit vous explique comment installer le kit de ventilation externe fourni en armoires sans cadre seulement. Si vous installez le kit de ventilation externe dans les armoires encadrée, alors s’il vous plaît se référer à ce guide pour des instructions à la place. Les instructions contenues dans ce livret sont un remplacement pour la sécurisation des instructions ventilation dans le guide principal. Après avoir monté le kit de ventilation externe à l’aide de cette livret, s’il vous plaît, puis renvoyer à vos instructions d’installation principaux pour terminer l’installation de votre lave-vaisselle.
Ensemble de ventilation externe (1)
Étrier et vis (1)
590452A
03.12
1a MODÈLES ENCASTRÉS UNIQUEMENT - PRÉPARATION POUR UNE VENTILATION EXTERNE AU TRAVERS DE LA
MÊME ARMOIRE
Les installations électriques et de plomberie peuvent être situées d'un côté ou de l'autre du lave-vaisselle.
Important! Veillez à ne pas couper à travers la plinthe ci-dessous
Important! S’assurer que tous les bois à nu sur les cadres de exposées sont suffisamment étanches pour résister à l’humidité (c.-à-polyuréthane résistant à l’humidité)
8 11⁄16 po (220 mm)
1” (25 mm) Cadre
MODÈLES ENCASTRÉS UNIQUEMENT - PRÉPARATION POUR UNE VENTILATION EXTERNE AU TRAVERS DE
1b L'ARMOIRE ADJACENTE ø 2 3⁄8 po 60 mm
Les installations électriques et de plomberie peuvent être situées d'un côté ou de l'autre du lave-vaisselle.
Vous devez agrandir le trou des raccordements ø 2 3⁄8 po (60 mm) en découpant le coin inférieur afin de permettre le passage du tuyau de ventilation supplémentaire.
TUYAU DE VENTILATION + TUYAU D'ÉVACUATION + TUYAU D'ALIMENTATION
Important! Veillez à ne pas couper à travers la plinthe ci-dessous
Ouvertures dans la tablette max. 3⁄16 po (5 mm)
ø max. 1½ po (38 mm)
ø 2 3⁄8 po (60 mm) Si les trous des raccordements sont pratiqués dans un panneau métallique, assurez-vous d'apposer le protecteur de rebord fourni autour du trou utilisé pour le cordon d'alimentation.
4 po (100 mm)
ø 2 3⁄8 po (60 mm)
8 11⁄16 po (220 mm)
CORDON D'ALIMENTATION
Important! S’assurer que tous les bois à nu sur les cadres de exposées sont suffisamment étanches pour résister à l’humidité (c.-à-polyuréthane résistant à l’humidité)
1” (25 mm) Cadre
2
2 DÉVISSER LE COUVERCLE SUPÉRIEUR DE
L’ÉVENT EXTERNE
3 LES ZONES OMBRÉES DOIVENT ÊTRE ENLEVÉS.
COMMENCEZ PAR DÉCOUPER FACE AVANT AVEC UN COUTEAU
Important!
19
4 COUPER EN PLASTIQUE DE RESTER
CHAQUE CÔTÉ
Score avec un couteau Casser
Assurez-vous d’effectuer cette étape sur une planche à découper ou similaire. Ne coupez pas sur le comptoir ou le plancher.
5 ASSEMBLAGE DU ÉVENT EXTERNE.
LE ÉVENT EST MAINTENANT MODIFIÉ ET PRÊT À INSTALLER
3
6 FIXER LE TUYAU DE L’ÉVENT ET POSITION
DANS LE TROU
7 FIXER LA ÉVENT EXTERNE À L’AIDE
SUPPORT & VIS
Important!
Assurez-vous que le tuyau d’évacuation a été fixée au coude équipée à l’arrière du produit (selon les instructions d’installation principales).
2
1
Après avoir acheminé le tuyau de ventilation au travers de l'ouverture, fixez l'évent à l'aide des quatre vis fournies.
Air flo
w
Insérez l’équerre dans l’orifice et sécuriser à l’étagère avec la vis
Vissez l’évent extérieur conjointement avec les 4 vis
44 Harbor Park Drive ... Connect the driver input/output wire to junction box wires as shown in Fig. 2, making sure that all wire connectors (D1) are secured.
VEHICLE LIFT LOCATIONS . .... Electric components . ..... Turbo control system preparation. ..... Before connecting the power wiring to the battery, check the ...
space that you are working on. WARNING: Risk of electric shock ... The Mounting Stake requires approximately a one (1) square foot hole to facilitate installation. The excavated should be approximately 14” deep, depending on your local code ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”.
... company's continuous improvement program. MAy, 2014 ... junction box (F1) using the junction box screws (B1). The side of the mounting plate marked “GND”.
MAy, 2014. INSTALLATION INSTRUCTION. Elemental - dwelLED ... (F1) using the junction box screws (B1).The side of the mounting plate marked “GND” must ...
To eliminate the risk of burns or fire by reaching over the .... Specified Rating of Power Supply. Cord Kit and Circuit. Protection. 120/240 Volts. 120/208 Volts.
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”.
... design of our products at any time as part of the company's continuous improvement program. ... Turn the lock switch to unlock position and circuit selection.
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax (516) 515.5050. Western Distribution Center. 1750 Archibald Ave • Ontario, CA ...
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. • Go to the main fuse box, ...
SAFETY INSTRUCTION. IMPORTANT: NEVER attempt any work without shutting off the electricity. • Read all instructions before installing. • System is intended ...
MAy, 2014. WARNING. IMPORTANT: ... plate (F1) by rotating the fixture frame. (G1) counter-clockwise. ... Secure the mounting plate (F1) to the junction box (E1) ...
www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
MAKE ELECTRICAL CONNECTION – U.S.A. ONLY . ..... Openings (such as a nearby window) ... connection for homes built after 1996, dryer circuits involved.
ApriL 3, 2017 12:22 pM. INSTALLATION INSTRUCTION .... (F1) using the junction box screws (B1).The side of the mounting plate marked “GND” must face out.
www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
MAy, 2014 ... Connect the canopy (E1), stems (F1) and the short stem (G1). ... House Wires. Green or Bare Copper. (Ground). A1. B1. C1. D1. E1. F1. G1. H1. J1.