space that you are working on. WARNING: Risk of electric shock ... The Mounting Stake requires approximately a one (1) square foot hole to facilitate installation. The excavated should be approximately 14” deep, depending on your local code ...
Read all instructions before installing. Place the wall switch in the “OFF” position. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the space that you are working on.
WARNING: Risk of electric shock. Install all luminaires 10 feet (3.05 m) or more from a pool, spa, or fountain. CAUTION: All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out AVERTISSEMENT IMPORTANT : COUPEZ L’ÉLECTRICITÉ AVANT TOUTE MANIPULATION. • Lisez toutes les instructions avant d’installer. • • Placez l’interrupteur mural en position d’arrêt (« OFF »). • Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »). MISE EN GARDE Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/cETL du luminaire.
Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050
Hex Key Qty: 1pc
Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
1
INSTALLATION INSTRUCTION PARK 12V 6651 INSTALLATION
1. 2.
Excavate a trench for the Mounting Stake. The Mounting Stake requires approximately a one (1) square foot hole to facilitate installation. The excavated should be approximately 14” deep, depending on your local code. This will allow the hex-head set screw on the Mounting Stake to remain above ground when the installation is completed.
3.
Secure Fixture Mounting Plate onto the Stake Metal Cap by using the Stake Mounting Screws.
4.
Secure the Stake Metal Cap assembly onto the Mounting Stake by tighten the Cap Mounting Screw (Note: Make sure the Fixture Mounting Plate is Oriented at desired position.)
5. 6.
Secure the Bollard Fixture on top of the Fixture Mounting Plate using the Fixture Mounting Screws. After proper wirings are done by using the outdoor rated wire
Bollard Fixture
Fixture Mounting Screw
Fixture Mounting Plate
Stake Mounting Screw Cap Mounting Screw
Stake Metal Cap
Mounting Stake
stable.
7.
Turn the main power supply back on and make sure the
CAUTION. - All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken.
(ie moisture-proof polyurethane). Important! Ensure you do not cut through the toekick below. Important! Ensure you do not cut through the toekick below.
44 Harbor Park Drive ... Connect the driver input/output wire to junction box wires as shown in Fig. 2, making sure that all wire connectors (D1) are secured.
VEHICLE LIFT LOCATIONS . .... Electric components . ..... Turbo control system preparation. ..... Before connecting the power wiring to the battery, check the ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”.
... company's continuous improvement program. MAy, 2014 ... junction box (F1) using the junction box screws (B1). The side of the mounting plate marked “GND”.
MAy, 2014. INSTALLATION INSTRUCTION. Elemental - dwelLED ... (F1) using the junction box screws (B1).The side of the mounting plate marked “GND” must ...
To eliminate the risk of burns or fire by reaching over the .... Specified Rating of Power Supply. Cord Kit and Circuit. Protection. 120/240 Volts. 120/208 Volts.
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”.
... design of our products at any time as part of the company's continuous improvement program. ... Turn the lock switch to unlock position and circuit selection.
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax (516) 515.5050. Western Distribution Center. 1750 Archibald Ave • Ontario, CA ...
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. • Go to the main fuse box, ...
SAFETY INSTRUCTION. IMPORTANT: NEVER attempt any work without shutting off the electricity. • Read all instructions before installing. • System is intended ...
MAy, 2014. WARNING. IMPORTANT: ... plate (F1) by rotating the fixture frame. (G1) counter-clockwise. ... Secure the mounting plate (F1) to the junction box (E1) ...
www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
MAKE ELECTRICAL CONNECTION – U.S.A. ONLY . ..... Openings (such as a nearby window) ... connection for homes built after 1996, dryer circuits involved.
ApriL 3, 2017 12:22 pM. INSTALLATION INSTRUCTION .... (F1) using the junction box screws (B1).The side of the mounting plate marked “GND” must face out.
www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
MAy, 2014 ... Connect the canopy (E1), stems (F1) and the short stem (G1). ... House Wires. Green or Bare Copper. (Ground). A1. B1. C1. D1. E1. F1. G1. H1. J1.