INSTALLATION INSTRUCTION Item#772 (New. 12/01/2011) READ AND SAVE THESE INSTRUCTIONS W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R . AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR ASSEMBLING THE FIXTURE (Fig. 1) 1. Shut off the power at the circuit
Fig. 1
breaker (avertissement! couper le courant au niveau des fusibles ou du disjoncteur) and remove the old fixture including the mounting hardware.
2.Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation. 3.Thread mounting screw (A) into the pre-drilled holes in the circular strap (B) spaced the same distance apart as the holes in the back-plate and secure with hex nut (C). 4.Attach the circular strap (B) to the junction box with junction box screws (D). The side of the circular strap marked “GND” must face out.
H Outlet Box I A B
G C
D
CONNECTING THE WIRES (Fig. 2) 5. At this point, connect the electrical wire as shown in Fig. 2, making sure that all wire connectors are secured. If your outlet has a ground wire (green or bare copper), connect the fixtures ground wire to it. Otherwise, connect the fixture ground wire directly to the circular strap using the green screw provided. After wires are connected, tuck them carefully inside the junction box. COMPLETING THE INSTALLATION (Fig. 1) 6. Place the fixture body (K) over the mounting screws (A) and secure tightly with cap nuts (E). 7. Place the candle sleeve (G) onto the socket (F). 8. Install the light bulb(s) (I) (not included) in accordance with the fixture’s specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!) 9. Clip the fabric shade(s) (H) onto the bulb(s). Hang the crystal drops (J) to the front edge of the metal leave on each arm. Your installation is now complete. Return the power to the junction box and test the fixture. Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
(ie moisture-proof polyurethane). Important! Ensure you do not cut through the toekick below. Important! Ensure you do not cut through the toekick below.
44 Harbor Park Drive ... Connect the driver input/output wire to junction box wires as shown in Fig. 2, making sure that all wire connectors (D1) are secured.
VEHICLE LIFT LOCATIONS . .... Electric components . ..... Turbo control system preparation. ..... Before connecting the power wiring to the battery, check the ...
space that you are working on. WARNING: Risk of electric shock ... The Mounting Stake requires approximately a one (1) square foot hole to facilitate installation. The excavated should be approximately 14” deep, depending on your local code ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”.
... company's continuous improvement program. MAy, 2014 ... junction box (F1) using the junction box screws (B1). The side of the mounting plate marked “GND”.
MAy, 2014. INSTALLATION INSTRUCTION. Elemental - dwelLED ... (F1) using the junction box screws (B1).The side of the mounting plate marked “GND” must ...
To eliminate the risk of burns or fire by reaching over the .... Specified Rating of Power Supply. Cord Kit and Circuit. Protection. 120/240 Volts. 120/208 Volts.
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”.
... design of our products at any time as part of the company's continuous improvement program. ... Turn the lock switch to unlock position and circuit selection.
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax (516) 515.5050. Western Distribution Center. 1750 Archibald Ave • Ontario, CA ...
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. • Go to the main fuse box, ...
SAFETY INSTRUCTION. IMPORTANT: NEVER attempt any work without shutting off the electricity. • Read all instructions before installing. • System is intended ...
MAy, 2014. WARNING. IMPORTANT: ... plate (F1) by rotating the fixture frame. (G1) counter-clockwise. ... Secure the mounting plate (F1) to the junction box (E1) ...
www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
MAKE ELECTRICAL CONNECTION – U.S.A. ONLY . ..... Openings (such as a nearby window) ... connection for homes built after 1996, dryer circuits involved.
ApriL 3, 2017 12:22 pM. INSTALLATION INSTRUCTION .... (F1) using the junction box screws (B1).The side of the mounting plate marked “GND” must face out.
www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
MAy, 2014 ... Connect the canopy (E1), stems (F1) and the short stem (G1). ... House Wires. Green or Bare Copper. (Ground). A1. B1. C1. D1. E1. F1. G1. H1. J1.
