www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
INSTALLATION INSTRUCTION 3020 LED Track Luminaires H-3020W, L-3020W, J-3020W
WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity. - Read all instructions before installing. - System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. - Place the wall switch in the “OFF” position. - Go to the main fuse box, or circuit breaker. Switch “OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on. AVERTISSEMENT IMPORTANT : Coupez l’électricité avant TOUTE manipulation. - Lisez toutes les instructions avant d’installer. - Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. - Placez l’interrupteur mural en position d’arrêt (« OFF »). - Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »). All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the UL/cUL listing of this fixture. OVERVIEW: Fixtures are designed for use on WAC Lighting’s track systems. LED TRACK FIXTURE
TRACK SYSTEMS
H-3020W Series
H Track
L-3020W Series
L Track
J-3020W Series
J and J2 Track
INSTALLING ON TRACK: 1. Align the alignment tab on the adapter with the groove/slot on the track (Figure 1).
1.
Alignment tab
2. Once aligned, insert adapter into track slot and rotate it 90°. The arrow should point to the grooved side of the track (Figure 2). 3. Make sure the alignment tab seats in the track slot 4. Reverse procedure to remove. Enter track luminaire may be positioned anywhere along the track length.
Insert the open end of the rail adapter into the rail and make sure that the contact points sit into the grooves of the rail. 4. Place the cap ring back onto the rail ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax ... August, 2014 ... System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. -. Place the ...
... of our products at any time as part of the company's continuous improvement .... power-up the fixture in order to allow the 0-10V dimming to function properly.
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax (516) 515.5050. Western Distribution Center. 1750 Archibald Ave • Ontario, CA ...
44 Harbor Park Drive. Port Washington, NY ... Wire Connector. Qty: 3 pcs ... Connect the driver input/output wire to junction box wires as shown in Fig. 2, making ...
June, 2014 ... Secure mounting backplate (D1) to the junction box (F1) ... White. (Neutral). House Wires. Green or Bare Copper. (Ground). F1. A1. D1. B1. C1. G1.
44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs, GA 30122. Western Distribution Center.
the circuit breaker switch(es) that control the power to the fixture or room that you are ... CAUTION When handling the fixture, do not apply pressure to the LEDs.
Note: Actual depth of box to be determined in accordance with the NEC and local ordinances. Indoor or outdoor frame mounted junction box: Raco 2” x4” (16.5 ...
Port Washington, NY 11050. Central Distribution ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker ...
Connect black fixture wire to hot wire, white fixture wire to neutral wire and green fixture wire to ground (as Fig.2). 5. Place all wiring and connectors back in ...
DeCember, 2014. 1 ... 4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to ...
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous ... Coloque el interruptor de ali mentación.
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
A) Recessed Mounting. NOTE: The back plate is not needed for recessed mounting and may be discarded. 1. Cut a 3 1/4â diameter hole in the surface. 2. Feed the fixture wires through the hole, and connect the wires to a 24V transformer. 3. Compress t
Headquarters/Eastern Distribution Center. 44 Harbor ... Western Distribution Center ... White or. Ribbed. Fixture Wires. Bare wire. (Ground). House Wires. Black.
(ie moisture-proof polyurethane). Important! Ensure you do not cut through the toekick below. Important! Ensure you do not cut through the toekick below.
Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs, GA 30122. Western Distribution Center. 1750 Archibald Avenue.
CAUTION. - All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken.
IMPORTANT: NEVER attempt any work without shutting off the electricity. -. Read all instructions before installing. -. System is intended for installation by a ...
Do not substitute any parts, leave parts out, or use any parts that are ... of our products at any time as part of the company's continuous improvement program.