INSTALLATION INSTRUCTION Mini LED Multiple Spots - New
Connect black fixture wire to hot wire, white fixture wire to neutral wire and green fixture wire to ground (as Fig.2). 5. Place all wiring and connectors back in ...
INSTALLATION INSTRUCTION Mini LED Multiple Spots - New Construction MT-3LD111NA-F30, MT-3LD211NA-F30, MT-3LD311NA-F30 SAFETY INSTRUCTION 1. Read all instructions before installing. 2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. 3. Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on. 4. Place the wall switch in the “OFF” position. INSTRUCTIONS DE SÉCURITÉ IMPORTANTES 1. Lisez toutes les instructions avant d’installer. 2. Système est destiné à être installé par un électricien qualifié en conformité avec le code national de 3. l’électricité et les règlements locaux. 4. Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt («OFF »). 5. Placez l’interrupteur mural en position d’arrêt (« OFF »). NEW CONSTRUCTION HOUSING MOUNTING: 1. Install mounting frame using two hanger bars, (24 1/2” max). Bars are notched on the ends to fit over “T” bars in suspended ceilings. Hanger bars include a captive mounting “screw-nail” for ease of installation (as Fig.1). Align the bottom of the hanger bar with the bottom of the wood joist. Secure the “screw-nail” on each end by screwdriver (as Fig.A), or by hammer (as Fig.B). 2. Slide fixture along bar hangers into desired location. Use locking screws to secure (as Fig.C). 3. Junction box is suitable for branch wiring and has trade size knockouts and integral non-metallic sheathed cable connectors. 4. Remove spring latched junction box door and connect fixture wires to building wires: insert each supply wire into appropriate junction box connector. Connect black fixture wire to hot wire, white fixture wire to neutral wire and green fixture wire to ground (as Fig.2). 5. Place all wiring and connectors back in wiring box and replace junction box door. 6. When installing in drywall, cut a hole 4 1/8”X4 1/8” in the drywall. Note: 3/4” inch maximum ceiling thickness. 7. Push the trim assembly up until the trim ring is flush to the ceiling (as Fig.3, Fig.4 and Fig.5). USE TEMPLATE SUPPLIED TO MAKE APPROPRIATE CUTOUT. Model
Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. June, 2014
INSTALLATION INSTRUCTION Mini LED Multiple Spots - Remodel MT-3LD111R-F30, MT-3LD211R-F30, MT-3LD311R-F30 SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. 1. Read all of these instructions before installing the track system. 2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. 3. Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on. 4. Place the wall switch in the “OFF” position. INSTRUCTIONS DE SÉCURITÉ IMPORTANTES 1. Lisez toutes les instructions avant d’installer. 2. Système est destiné à être installé par un électricien qualifié en conformité avec le code national de 3. l’électricité et les règlements locaux. 4. Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt («OFF »). 5. Placez l’interrupteur mural en position d’arrêt (« OFF »). REMODEL HOUSING MOUNTING: 1. Cut out a hole in the existing ceiling (as Fig.1). 2. Pull ceiling wire through the hole (as Fig.2). 3. Junction box is suitable for chain wiring of multiple fixtures and is supplied with a slide latch door, and two trade size knockouts connectors. 4. Remove junction box door and connect fixture wires to building wires: insert each supply wire into appropriate junction box connector. Connect black fixture wire to hot wire, white fixture wire to neutral wire and green fixture wire to ground (as Fig.3 and Fig.4). 5. Place all wiring and connectors back in wiring box and replace junction box door. 6. Push the housing up through the hole (as Fig.5). 7. Push clips to secure the fixture. Note: 1 inch maximum ceiling thickness (as Fig.6). 8. Push the trim assembly up until the trim ring is flush to the ceiling (as Fig.7, Fig.8, Fig.9 and Fig.10). USE TEMPLATE SUPPLIED TO MAKE APPROPRIATE CUTOUT. Model
IMPORTANT: NEVER attempt any work without shutting off the electricity. -. Read all instructions before installing. -. System is intended for installation by a ...
... of our products at any time as part of the company's continuous improvement .... power-up the fixture in order to allow the 0-10V dimming to function properly.
www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax (516) 515.5050. Western Distribution Center. 1750 Archibald Ave • Ontario, CA ...
44 Harbor Park Drive. Port Washington, NY ... Wire Connector. Qty: 3 pcs ... Connect the driver input/output wire to junction box wires as shown in Fig. 2, making ...
Insert the open end of the rail adapter into the rail and make sure that the contact points sit into the grooves of the rail. 4. Place the cap ring back onto the rail ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax ... August, 2014 ... System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. -. Place the ...
June, 2014 ... Secure mounting backplate (D1) to the junction box (F1) ... White. (Neutral). House Wires. Green or Bare Copper. (Ground). F1. A1. D1. B1. C1. G1.
44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs, GA 30122. Western Distribution Center.
the circuit breaker switch(es) that control the power to the fixture or room that you are ... CAUTION When handling the fixture, do not apply pressure to the LEDs.
Note: Actual depth of box to be determined in accordance with the NEC and local ordinances. Indoor or outdoor frame mounted junction box: Raco 2” x4” (16.5 ...
Port Washington, NY 11050. Central Distribution ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker ...
DeCember, 2014. 1 ... 4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to ...
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous ... Coloque el interruptor de ali mentación.
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
A) Recessed Mounting. NOTE: The back plate is not needed for recessed mounting and may be discarded. 1. Cut a 3 1/4â diameter hole in the surface. 2. Feed the fixture wires through the hole, and connect the wires to a 24V transformer. 3. Compress t
Headquarters/Eastern Distribution Center. 44 Harbor ... Western Distribution Center ... White or. Ribbed. Fixture Wires. Bare wire. (Ground). House Wires. Black.
Do not view the beam directly with optical instruments such as magnifiers. ...... produit Adam Hall serait sujet à des défaillances répétées, Adam Hall, à sa disc-.
dispositivo non contiene parti che possono essere riparate o sottoposte a manutenzione da parte dell'utente. Per gli interventi di manutenzione e .... compte quatre groupes de couleurs (rouge, vert, bleu, blanc), dont l'intensité est contrôlable indi
Please, take a few moments to read these instructions carefully, as we want you to enjoy your new Cameo Lights products quickly and to ... When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. .
im unteren DMX-Wertebereich grober und im oberen DMX-Wertebereich feiner einstellen. Dimmerkurve 04CU / 08CU S-Kurve: Die Lichtintensität lässt sich im unteren und oberen DMX-Wertebereich fein und im mittleren DMX-Wertebe- reich grob einstellen. Dimm
(ie moisture-proof polyurethane). Important! Ensure you do not cut through the toekick below. Important! Ensure you do not cut through the toekick below.
Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs, GA 30122. Western Distribution Center. 1750 Archibald Avenue.