... design of our products at any time as part of the company's continuous improvement program. ... Turn the lock switch to unlock position and circuit selection.
INSTALLATION INSTRUCTION Quick Connect® Adapter - W Track EN-WQ50AR WARNING: IMPORTANT: NEVER attempt any work without shutting off the electricity. • Read all instructions before installing. • System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. • Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on. • Place the wall switch in the “OFF” position. AVERTISSEMENT IMPORTANT : Coupez l’électricité avant TOUTE manipulation. • Lisez toutes les instructions avant d’installer. • Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. • Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »). • Placez l’interrupteur mural en position d’arrêt (« OFF »). INSTALLING ON TRACK 1. Insert the Quick Connector with decorative ring into Quick Connect® adapter (Fig 1). Then twist to tighten the connection. 2.
Quick Connect™ Adapter
Turn the lock switch to unlock position and circuit selection handle is in the off position. (Fig 2).
Decorative Ring Quick Connector
3.
Align the alignment tab on the adapter with the groove/slot on the W track (Fig 3). Once aligned, insert adapter into the track.
4.
Secure the fixture to the track by turning the lock switch to its locked position. (Fig 4)
5.
Select the circuit you want the luminaire to be powered on by rotating the circuit selection handle to circuit 1 or 2. (View A)
6.
Fig.1
Switch the main fuse breaker and circuit breaker back to “ON” position.
Fig.2
W Track
Adapter
Circuit selection handle (power off position)
Lock switch (Unlock position)
Fig.3
Groove Alignment tab
Fig.4
2
1
View. A
Circuit selection handle 1. Power on at circuit 1 2. Power on at circuit 2 WAC Lighting www.waclighting.com Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050
View A
Lock switch (lock position)
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. December, 2014
Phase (HILIC). Max Pressure. 8,000 psi 8,000 psi. Max Temp. 125°C. 125°C. pH Range. 2 - 10.1. 2 - 8.0. 40mm x 2.1mm Column Shown. For more information ...
(ie moisture-proof polyurethane). Important! Ensure you do not cut through the toekick below. Important! Ensure you do not cut through the toekick below.
If you have a D-Link Cloud Router, you can take advantage of Zero Configuration Setup. This feature automatically configures your camera's settings for you and adds it to your mydlink account. If you do not have a D-Link Cloud Router, you can use the
Jan 10, 2001 - Select â Specify the location of the driver (Advanced) â and click on Next to ... The proper procedure is to install the U2IrDA adapter and driver ...
44 Harbor Park Drive ... Connect the driver input/output wire to junction box wires as shown in Fig. 2, making sure that all wire connectors (D1) are secured.
VEHICLE LIFT LOCATIONS . .... Electric components . ..... Turbo control system preparation. ..... Before connecting the power wiring to the battery, check the ...
space that you are working on. WARNING: Risk of electric shock ... The Mounting Stake requires approximately a one (1) square foot hole to facilitate installation. The excavated should be approximately 14” deep, depending on your local code ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”.
... company's continuous improvement program. MAy, 2014 ... junction box (F1) using the junction box screws (B1). The side of the mounting plate marked “GND”.
MAy, 2014. INSTALLATION INSTRUCTION. Elemental - dwelLED ... (F1) using the junction box screws (B1).The side of the mounting plate marked “GND” must ...
To eliminate the risk of burns or fire by reaching over the .... Specified Rating of Power Supply. Cord Kit and Circuit. Protection. 120/240 Volts. 120/208 Volts.
settings will erase all its programming and will require the Lutron Connect Bridge to be reactivated into the system. 1. Triple tap and hold the âAddâ button. DO NOT release ... Ambient operating temperature: 32 °F to 104 °F. (0 °C to 40 °C),
Pour toute question relative à votre abonnement, votre identifiant/login/mot de passe, contactez le Service Relations Clients au 01 41 05 22 22. * (0,15 â¬/min) ...
second. Release the reset button at this time to load Ethernet defaults (IP=192.168.127.254; ... English button to open the pdf version of the NPort 6110 User's.
(See APP setup procedure for phone mode settings). * Set up backlight and service reminder when entering the setup mode the second time. Lorsque vous ...
If you have a D0Link Cloud Router, you can take advantage of Zero Configuration Setup. This feature automatically configures your camera,s settings for you and adds it to your mydlink account. If you do not have a D.Link Cloud Router, you can use the
(See APP setup procedure for phone mode settings). * Set up backlight and service reminder when entering the setup mode the second time. Lorsque vous ...