Lismore 9 Light Chandelier. 1.1. F2937-3-6. Chandelier. F2937/3+6. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed ...
Chandelier GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for dry locations only.
1A 5
3
LAMP
HUB
4 SHADE
4
2
CANDLE TUBE
1
SOCKET
4
4 UPPER TIER
5
5 FIXTURE ARM
5
5
LOWER TIER
1
Install the candle tube by slipping it through the socket.
2
Install the shade by placing it over the candle tube.
3
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. Repeat steps 1-3 for remaining sockets.
4
Using the help of another person, connect the upper tier of the chandelier to the hub by hooking each fixture arm into the corresponding hook.
5
Using the help of another person, connect the lower tier of the chandelier to the upper tier by hooking each fixture arm into the corresponding hook.
6
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. 1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A 5
3
AMPOULE
MOYEU
4 ABAT-JOUR
4
2
TUBE BOUGIE
1
DOUILLE
4
4 NIVEAU SUPÉRIEUR
5
5 BRAS DE LUMINAIRE
5
5 NIVEAU INFÉRIEUR
1
Installer le tube bougie en glissant à travers le socket.
2
Installer l'abat-jour en le plaçant sur le tube bougie.
3
Vissez l'ampoule dans la douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage. Répétez les étapes 1 à 3 pour les douilles restants.
4
À l'aide d'une autre personne, connectez le niveau supérieur à le moyeu par accrochage de chaque bras du luminaire dans les crochets correspondants.
5
À l'aide d'une autre personne, connecter le niveau inférieur à le niveau supérieur par accrochage de chaque bras du luminaire dans les crochets correspondants.
6
Reportez-vous aux instructions pour supplément clos électrique et installation de luminaire sur boîte de sortie de maison.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A 5
3
BOMBILLA
EJE
4 PANTALLA
4
2
TUBO DE LA VELA
1
ENCHUFE
4
4 NIVEL SUPERIOR
5
5 BRAZO DE LA LÁMPARA
5
5 NIVEL INFERIOR
1
Instale el tubo de vela lo deslizándose a través del enchufe.
2
Instale la pantalla colocándola sobre el tubo de vela.
3
Enrosque la bombilla en el enchufe. Consulte la etiqueta en el zócalo de la lámpara para obtener información de Max Wattage. Repita los pasos 1-3 para los enchufes restantes.
4
Con la ayuda de otra persona, conecte el nivel superior a el eje enganchando cada brazo de la lámpara en los ganchos correspondientes.
5
Con la ayuda de otra persona, conecte el nivel inferior a el nivel superior enganchando cada brazo de la lámpara en los ganchos correspondientes.
6
Siga las instrucciones de Instalación incluido suplemento para eléctricos y instalación de la lámpara en la caja de enchufe de casa.
P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing ... Refer to the label on the lamp socket for Max Wattage information.
Install the top cover to the fixture, install the bottom cover to the top cover, and secure them together by screwing the finial onto the top cover. Follow enclosed ...
código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de ...
instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone. Conductores de alimentacion ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamp into the socket. Refer to the label ...
the applicable installation code by a person familiar with the ... Use minimum 90°c supply conductors. 4. 1. 2. 3. 3. 4. CAP NUT. THREADED NIPPLE. 3 ...
Conecte la lámpara a una tierra apropiada de acuerdo con los códigos eléctricos ... y / o rígido) al cable de la línea eléctrica neutra con una tuerca para cable.
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the lamp ...
Pediment 3 Light Outdoor Post. 1.1. OL11107. OL11107. Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
Install the bottom tier to the top tier by screwing the fixture arms to the swivels and bottom of the top tier. Assemble the top tier by screwing the fixture arms to the ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 1. 2. 3.
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SMALL ORNAMENT. THUMB SCREW. 7. F
Split wires and strip off 3/4" of insulation from each end. C. Follow enclosed ”Fixture installation instructions” for electrical and fixture installation onto.
Hamlet 5 and 9 Light Chandelier. 1.0. F3065-5-F3066-9. Chandelier. F3065/5, F3066/9. 1A. 1. CAUTION RISK OF FIRE. -. This product must be installed in ...
junction boxes. This product is suitable for dry locations only. This product may be dimmed with a standard incandescent dimmer. Feed the cord through the ...
Instalar los seguidores de la vela por su inclusión en la parte superior de los tubos de la vela. . Consulte la etiqueta del casquillo de la lámpara para obtener ...
Install the fixture arms by screwing them to the swivels, then secure them to the hub using the washers and couplers. Place the shade onto the shade base and ...
Connect the black fixture wire to the hot power line wire with a wire nut. Align the keyed slots ... the hazards involved. Use minimum 90°c supply conductors. G. P.
Drill appropriate size holes at the marked locations and install the anchors. ... This product is safety listed for damp locations. ... CAUTION RISK OF FIRE.
These fixtures are intended to be installed utilizing compliant junction. NEC boxes. This product is safety listed for damp locations. Incandescent lamps may be ...
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes . Consulte la etiqueta del casquillo de la lámpara para obtener información Max.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...