Drill appropriate size holes at the marked locations and install the anchors. ... This product is safety listed for damp locations. ... CAUTION RISK OF FIRE.
Wall GENERAL PRODUCT INFORMATION: CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations.
Use minimum 90°c supply conductors.
For a complete list of dimmers, visit out website at www.Feiss.com
1A ANCHOR
ANCHOR SCREW
PLATE AND CAP SCREW
JUNCTION BOX
3
11
5 10
DIFFUSER
7
BRACKET
8 MOUNTING PLATE
3
5
SET SCREW
9 ALLEN KEY
1
Temporarily install the mounting plate to the junction box.
2
Mark the anchor hole locations on the mounting plate and remove the mounting plate.
3
Drill appropriate size holes at the marked locations and install the anchors.
4
Secure the mounting plate to the junction box.
5
Screw the anchor screws into the anchors.
6
Connect the fixture to a suitable ground in accordance with local electrical codes.
7
Connect the white fixture wire to the neutral power line wire with a wire nut.
8
Connect the black fixture wire to the hot power line wire with a wire nut.
9
Mount the fixture base onto the mounting plate and secure it with the set screw using an Allen key.
10
Install the plate to the fixture and secure it in place using the cap screws.
11
Install the diffuser by carefully sliding it into the bracket until secure.
1
1.0
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c. 1A ANCRE
VIS DE ANCRE
PLAQUE ET VIS CAPUCHON
BOÎTE DE JONCTION
3
11
5 10
DIFFUSEUR
7
SUPPORT
8 PLAQUE DE MONTAGE
3
5
VIS DE RÉGLAGE
9 CLÉ ALLEN
1
Installer temporairement la plaque de montage à la boîte de jonction.
2
Marquer les emplacements des trous d'ancre sur la plaque de montage et enlever la plaque de montage.
3
Percer des trous de la taille appropriée aux emplacements marqués et installez les ancres.
4
Fixez la plaque de montage à la boîte de jonction.
5
Visser les vis d'ancres dans l’ancres.
6
Connectez le luminaire à un terrain approprié conformément aux codes électriques locaux.
7
Connectez le fil blanc de luminaire au fil de la ligne d'alimentation neutre avec un écrou de fil.
8
Connectez le fil noir de luminaire au fil de la ligne d'alimentation chaude avec un écrou de fil.
9
Montez la base de luminaire sur la plaque de montage et le fixer avec les vis de réglage en utilisant la clé Allen.
10
Installez la plaque à la luminaire et le fixer en place à l'aide des vis capuchon.
11
Installez le diffuseur en le faisant glisser avec précaution dans le support jusqu'à ce que la sécurité.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min.
1A
TORNILLO DE ANCLAJE PLACA Y TORNILLO CAPUCHON
ANCLAJE
CAJA DE JUNCTURA
3
11
5 10
DIFUSOR
7
SOPORTE
8 PLACE DE MONTAJE
3
5
9
TORNILLO DE FIJACIÓN
LLAVE ALLEN
1
Instalar temporalmente la placa de montaje a la caja de juntura.
2
Marque las ubicaciones de los orificios de anclaje en la placa de montaje y retire la placa de montaje.
3
Taladro agujeros de tamaño apropiado en los lugares marcados y instalar los anclajes.
4
Fije la placa de montaje a la caja de junctura.
5
Atornille los tornillos de anclaje en los anclajes.
6
Conecte el lámpara a una tierra adecuada, de acuerdo con los códigos eléctricos locales.
7
Conecte el cable blanco de la lámpara al cable de línea de energía neutra con una tuerca para cable.
8
Conecte el cable negro de la lámpara al cable de línea eléctrica caliente con una tuerca para cable.
9
Monte la base de lámpara sobre la placa de montaje y fijarlo con los tornillos de fijación usando la llave Allen.
10
Instalar la placa para la lámpara y fijarlo en su lugar con los tornillos capuchon.
11
Instalar el difusor deslizando con cuidado en el soporte hasta que quede firme.
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
Disconnect or turn off power before installation or servicing. ▻ Verify that supply ... Allow for some volume of airspace around the fixture. Avoid covering LED ...
Split wires and strip off 3/4" of insulation from each end. C. Follow enclosed ”Fixture installation instructions” for electrical and fixture installation onto.
Connect the black fixture wire to the hot power line wire with a wire nut. Align the keyed slots ... the hazards involved. Use minimum 90°c supply conductors. G. P.
These fixtures are intended to be installed utilizing compliant junction. NEC boxes. This product is safety listed for damp locations. Incandescent lamps may be ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamp into the socket. Refer to the label ...
the applicable installation code by a person familiar with the ... Use minimum 90°c supply conductors. 4. 1. 2. 3. 3. 4. CAP NUT. THREADED NIPPLE. 3 ...
Conecte la lámpara a una tierra apropiada de acuerdo con los códigos eléctricos ... y / o rígido) al cable de la línea eléctrica neutra con una tuerca para cable.
Do not substitute any parts, leave parts out, or use any parts that are ... of our products at any time as part of the company's continuous improvement program.
Lismore 9 Light Chandelier. 1.1. F2937-3-6. Chandelier. F2937/3+6. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed ...
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the lamp ...
Pediment 3 Light Outdoor Post. 1.1. OL11107. OL11107. Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white ...
Before commencing installation or maintenance, ensure electricity is switched off at the mains. 1. Fit the mounting bracket in the required position. Be aware of ...
P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing ... Refer to the label on the lamp socket for Max Wattage information.
While holding reflector cone or baffle in place, align three ... CONSTRUCTION recessed cans, please use the .... wise to release trim ring and reflector cone or.
Turn power OFF to the fixture. 2. Remove existing T8 4FT fluorescent lamp from the fixture. 3. Inspect the sockets and wiring to ensure they are in proper working ...
Beware of joists, water pipes and electric cables when drilling holes. 2. ... Aurora does not levy any WEEE disposal charges to its customers for affected WEEE.
Connect the white driver wire to the neutral power line wire with a wire nut. ... Insert the glass panels into the housing and secure them using the glass panel ...