P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing ... Refer to the label on the lamp socket for Max Wattage information.
Chandelier GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for dry locations only.
1A
2
1
DECORATIVE FRAME
STEM
5
SHADE
4
LAMP
3
CANDLE TUBE
1
SOCKET
FIXTURE
SHADE BASE
1
Screw the stem to the fixture, then screw the stem to the decorative frame.
2
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
3
Install the candle tube by slipping it through the socket.
4
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
5
Install the shade by properly placing it over the lamp and into the shade base. Repeat steps 3-5 for remaining shades.
1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
2
1
CADRE DÉCORATIF
TIGE
5
ABAT-JOUR
4
AMPOULE
3
TUBE BOUGIE
1
DOUILLE
LUMINAIRE
BASE D’ABAT-JOUR
1
Vissez la tige sur le luminaire, puis vissez la tige pour le cadre décoratif.
2
Suivez supplément ci-joint des instructions électriques et installation d'accessoires dans la boîte de prise de maison.
3
Installez le tubes de bougie en les glissant à travers le douille.
4
Vissez le ampoule dans le douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
5
Installer l'abat-jour en le plaçant correctement sur le ampoule et dans la base de l'abat-jour. Répétez les étapes 3 à 5 pour les autres abat-jours.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
2
1
MARCO DECORATIVO
TALLO
5
PANTALLA
4
BOMBILLA
3
TUBO DE VELA
1
ENCHUFE
LÁMPARA
BASE DE LA PANTALLA
1
Atornille el tallo a la lámpara y, luego atornillar el tallo al marco decorativo.
2
Siga las instrucciones de instalación incluido suplemento para eléctricos y instalación de la lámpara en caja de salida de la casa.
3
Instale el tubo de vela deslizándolo a través de el enchufe.
4
Atornille la bombilla en el enchufe. Consulte la etiqueta en el zócalo de la lámpara para obtener información de Max Wattage.
5
Instalar la pantalla colocando correctamente sobre la bombilla y en el base de la pantalla. Repita los pasos 3-5 para pantallas restantes.
Lismore 9 Light Chandelier. 1.1. F2937-3-6. Chandelier. F2937/3+6. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed ...
Install the top cover to the fixture, install the bottom cover to the top cover, and secure them together by screwing the finial onto the top cover. Follow enclosed ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamp into the socket. Refer to the label ...
the applicable installation code by a person familiar with the ... Use minimum 90°c supply conductors. 4. 1. 2. 3. 3. 4. CAP NUT. THREADED NIPPLE. 3 ...
Conecte la lámpara a una tierra apropiada de acuerdo con los códigos eléctricos ... y / o rígido) al cable de la línea eléctrica neutra con una tuerca para cable.
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the lamp ...
Pediment 3 Light Outdoor Post. 1.1. OL11107. OL11107. Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
Instale los tubos de la vela por el deslizamiento de ellos en los . enchufes . Consulte la etiqueta del casquillo de la lámpara para obtener información Max.
DeWitt 4 Light Foyer Chandelier. 1.0. F3072-4. Chandelier. F3072/4. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed ...
Refer to the label on the lamp socket for Max Wattage information. Install and secure the string of beads by hooking them to the top and bottom of the fixture.
Installez les tubes de bougies en les glissant sur les douilles. Installez les suiveurs de la bougie au sommet des tubes de bougies. Vissez l'ampoules dans les ...
Split wires and strip off 3/4" of insulation from each end. C. Follow enclosed ”Fixture installation instructions” for electrical and fixture installation onto.
Connect the black fixture wire to the hot power line wire with a wire nut. Align the keyed slots ... the hazards involved. Use minimum 90°c supply conductors. G. P.
Install the fixture arms by screwing them to the swivels, then secure them to the hub using the washers and couplers. Place the shade onto the shade base and ...
Drill appropriate size holes at the marked locations and install the anchors. ... This product is safety listed for damp locations. ... CAUTION RISK OF FIRE.
These fixtures are intended to be installed utilizing compliant junction. NEC boxes. This product is safety listed for damp locations. Incandescent lamps may be ...
Connect the fixture to a suitable ground in accordance to local electrical codes. ... Neatly place all the wires into the junction box, place the canopy onto the ...