VVT Sensor (Camshaft Position Sensor) Circuit Range/Performance Problem
CIRCUIT DESCRIPTION Refer to DTC P1345 (VVT Sensor (Camshaft Position Sensor ) Circuit Malfunction) on page DI-1 19. DTC No.
Detection Item
Trouble Area
P1346
Deviation in crankshaft position sensor signal and VVT sensor (bank 1) signal (2 trip detection logic)
Mechanical system malfunction (Skipping teeth of timing belt, belt stretched) ECM
WIRING DIAGRAM Refer to DTC P1345 (VVT Sensor (Camshaft Position Sensor ) Circuit Malfunction) on page DI-1 19 for the WIRING DIAGRAM.
INSPECTION PROCEDURE HINT: Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame records the engine conditions when the malfunction is detected, when troubleshooting it is useful for determining whether the vehicle was running or stopped, the engine warmed up or not, the air-fuel ratio lean or rich, etc. at the time of the malfunction.
1
Check valve timing (Check for loose and jumping teeth of timing chain) (See page EM-15 ).
NG
Adjust valve timing (Repair or replace timing chain).
VVT sensor (VVT signal) consist of a signal plate and pickup coil. The VVT signal plate has 1 tooth on its ... Trouble Area. No VVT sensor signal to ECM during ...
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because ... During cranking or idling, check between terminals G2 and. NE-, NE ...
jumper wires from VW 1594 test kit. Specified value: approx.1000. - Replace Crankshaft Position (CKP) sensor. - Connect multimeter between terminal 1 and 3 ...
8 Angular-position sensors. A. B. Throttle-valve angular-position sensor. Measurement of angles up to 88°. 0. 0. 0,05. 0,94. 1,00. Angle of rotationÏ. V.
The No.1 vehicle speed sensor outputs a 4-pulse signal for every revolution of ... â¢Open or short in vehicle speed sensor circuit ... INSPECTION PROCEDURE.
2. 1. R-W. R-B. ECM. OCV+. OCV-. 10. 23. E7. E7. DI-122. -. DIAGNOSTICS. ENGINE ... (b) Connect the TOYOTA hand-held tester and select VVT from ACTIVE TEST menu. CHECK: ... Replace oil control valve, and then go to step 6. OK. 6.
The knock sensor is fitted to the cylinder block to detect engine knocking. This sensor contains a piezoelec- tric element which generates a voltage when it ...
Bank 1 refers to the bank that includes cylinder No.1. â¢. Sensor 1 refers to the sensor closer to the engine body. â¢. Sensor 2 refers to the sensor farther away from ...
Figure 2. 5. Run the cable through the printer as show on picture 3. The connector will be connected to the DIMM (on. 4200-4300) or CompactFlash (on ...
Voltage output of the heated oxygen sensor remains at 0.40 V or more, or 0.50 V or less when the vehicle is driven at 40 km/h. (25 mph) or more after the engine ...
à côté de cette option sera cochée lorsque l'option est activée. Votre capteur de .... est connectée en A0, la DEL verte en A1 et la DEL bleue en A2. Vous pouvez.
Boîtier en matière isolante auto-extinguible. Sens du courant secondaire : Un ... Rapport de transformation (NP/NS). : 1/4000. Secondary current (IS) at IPN.
Measuring electronic sensor of d.c., a.c., and pulsating voltages with an insulation between primary and secondary circuits. Capteur électronique de mesure de ...
REMOVE DIRECT CLUTCH SPEED SENSOR. (a) Disconnect the connector. (b) Remove the bolt and direct clutch speed sensor. (c) Remove the O-ring from the ...
This product contains chemicals known to the State of California to cause cancer and/or ... NOTE: The illustrations in this manual may not look the same as your product, but your ..... currents, such as batteries and power cables, are also examples o