jumper wires from VW 1594 test kit. Specified value: approx.1000. - Replace Crankshaft Position (CKP) sensor. - Connect multimeter between terminal 1 and 3 ...
Crankshaft Position (CKP) sensor, checking Component locations
page 28-1 .
All sensors correctly installed, securely connected - Disconnect (black) harness connector. - Switch Fluke 83 multimeter to resistance range and connect between CKP sensor connector terminals 1 and 2 (in connector bracket) using jumper wires from VW 1594 test kit. Specified value: approx.1000 If the specified value is not obtained: - Replace Crankshaft Position (CKP) sensor. If the specified value is obtained: - Connect multimeter between terminal 1 and 3 (GND), then between terminals 2 and 3 (GND). Specified value: infinite
(open)
If the specified value is not obtained: - Replace Crankshaft Position (CKP) sensor.
- Connect VAG 1598/19 test box to ECM harness connector page 01-255 . - Check CKP sensor shielding for continuity by connecting multimeter between terminal 3 and engine Ground (GND). Specified value: max. 1 - Check wiring for continuity between CKP sensor connector terminal 1 and test box socket A9, then between CKP sensor connector terminal 2 and test box socket A10. Specified value: max. 1 If the specified values are not obtained: - Eliminate short or open circuit in wiring. CKP sensor terminal number
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because ... During cranking or idling, check between terminals G2 and. NE-, NE ...
Nov 22, 2002 - The first position of the 3 digit display (Heater) fluctuate at certain operating conditions between 0 and 1. Page 7 of 61. Oxygen sensor control ...
VVT sensor (VVT signal) consist of a signal plate and pickup coil. The VVT signal plate has 1 tooth on its ... Trouble Area. No VVT sensor signal to ECM during ...
When installing the crankcase, do not use an iron hammer to tap it. ⢠The following parts must be ... CRANKCASE ASSEMBLY. Clean off all gasket material from ...
8 Angular-position sensors. A. B. Throttle-valve angular-position sensor. Measurement of angles up to 88°. 0. 0. 0,05. 0,94. 1,00. Angle of rotationÏ. V.
motorcycle in case specifications are changed. .... Torque specifications listed below are for important fasteners. ..... â¡Worn piston pin and connecting rod.
Connecting rod big end radial clearance. 0 â 0.008 (0 ... SPECIFICATIONS. UNIT: mm (in) .... Section 1 through 3 apply to the whole motorcycle, while section 4 ...
seems to me that the controllers would have to call only those contacts with a proximity and an altitude ... lemen, I am sorry for the delay, but it looks as though ...
Nov 23, 2002 - Check signal wire for continuity between harness connector terminal 2. (in engine compartment) and test box socket A13. Specified value: max.
sensitivity (Ics) is the required amount of current flowing ... culated: Ics = Vsen/Rm. Professor. Ralph Santoro ... operational amplifier (OP-AMP) and then to the ...
Edit distance. Implementation. Python Implementation import numpy as np def levenshtein(s1, s2):. "Calculates the Levenshtein distance between a and b.".
when the battery is being charged or discharged. A QUICK CHECK. An easy method of ..... (Capacitors (2) 470 mierofarads at. 10 volts (Cl, C2) (RS #272-1018).
ble value of Young's Modulus across the grain in Yellow. Birch is approximately Ej ... plate should be made of %" thick 2024-T4 aluminum or metal of equivalent ...
