Bank 1 refers to the bank that includes cylinder No.1. â¢. Sensor 1 refers to the sensor closer to the engine body. â¢. Sensor 2 refers to the sensor farther away from ...
CIRCUIT DESCRIPTION Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI-43 . DTC No.
P0135 P0141
DTC Detecting Condition When the heater operates, heater current exceeds 2 A (2 trip detection logic) Heater current of 0.2 A or less when the heater operates (2 trip detection logic)
Trouble Area Open or short in heater circuit of heated oxygen sensor Heated H t d oxygen sensor heater h t ECM
HINT:
Bank 1 refers to the bank that includes cylinder No.1. Sensor 1 refers to the sensor closer to the engine body. Sensor 2 refers to the sensor farther away from the engine body.
WIRING DIAGRAM Refer to DTC P0125 on page DI-43 for the WIRING DIAGRAM.
INSPECTION PROCEDURE HINT: Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame records the engine conditions when the malfunction is detected, when troubleshooting it is useful for determining whether the vehicle was running or stopped, the engine warmed up or not, the air-fuel ratio lean or rich, etc. at the time of the malfunction.
2002 ECHO (RM884U)
Author:
Date:
225
DI-56 DIAGNOSTICS
1
-
ENGINE
Check voltage between terminals HT, HT2 of ECM connectors and body ground. ON
HT
(+) HT2
(-) A09037
PREPARATION: (a) Remove the connector cover from the ECM. (b) Turn the ignition switch ON. CHECK: Measure voltage between terminals HT, HT2 of ECM connectors and body ground. HINT: Connect terminal HT to bank 1 sensor 1. Connect terminal HT2 to bank 1 sensor 2. OK: Voltage: 9 - 14 V OK
Check and replace ECM (See page IN-29 ).
NG
2
Check resistance of heated oxygen sensor heater (See page SF-60 ).
NG
Replace heated oxygen sensor.
OK
Check and repair harness or connector between EFI main relay (Marking: EFI), heated oxygen sensor and ECM (See page IN-29 ).
Voltage output of the heated oxygen sensor remains at 0.40 V or more, or 0.50 V or less when the vehicle is driven at 40 km/h. (25 mph) or more after the engine ...
The knock sensor is fitted to the cylinder block to detect engine knocking. This sensor contains a piezoelec- tric element which generates a voltage when it ...
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because ... During cranking or idling, check between terminals G2 and. NE-, NE ...
Nov 22, 2002 - The first position of the 3 digit display (Heater) fluctuate at certain operating conditions between 0 and 1. Page 7 of 61. Oxygen sensor control ...
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because ... CHECK: Measure voltage between terminals IGF of the ECM connector.
The No.1 vehicle speed sensor outputs a 4-pulse signal for every revolution of ... â¢Open or short in vehicle speed sensor circuit ... INSPECTION PROCEDURE.
CIRCUIT DESCRIPTION. The vehicle speed sensor outputs a 4-pulse signal for every revolution of the transaxle output shaft. After this signal is converted into a ...
O2_Closed_Loop = O2 closed loop adjustment factor in percent ... The mode of operation of the VE tuning using O2 sensor crossing points is quite simple - all ...
flow ratio from âCURRENT DATAâ. Mass Air Flow Value (gm/sec.) Malfunction. 0.0. â¢Mass air flow meter power source circuit open. â¢VG circuit open or short.
plied to the intake air temp. sensor from the terminal THA via ... After confirming DTC P0110, use the OBD II scan tool or TOYOTA hand-held tester to confirm the ...
Shift solenoid valve ST is switched ON-OFF by a signal from ECM so that let in or out timing of 2nd brake is adjusted by operating orifice control valve. Therefore ...
26 mai 2015 - Close the window. 4. Increase the temperature setting. 5. Select the higher power setting. 2. The set temperature is lower than the current room.
Issue date: 01.2002. Installation Jit for Eront Seat Geating System. MINI 'R50/R53( KGD and RGD. The installation time is approx. 3.0 hours, but this may vary ...
