INSTALLATION INSTRUCTION Aether 3.5” IC Remodel Housing HR-3LED-R15A SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. • Read all instructions before installing. • System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. • Place the wall switch in the “OFF” position. • Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the space that you are working on. CAUTION: All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/cETL listing of this fixture. AVERTISSEMENT IMPORTANT : COUPEZ L’ÉLECTRICITÉ AVANT TOUTE MANIPULATION. • Lisez toutes les instructions avant d’installer. • Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. • Placez l’interrupteur mural en position d’arrêt (« OFF »). • Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »).
•
MISE EN GARDE Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/cETL du luminaire. OVERVIEW: Housing is Remodel IC, AIRTIGHT. Housing requires a trim for finished look. Check catalog for various trims choices. HOUSING INSTALLATION: 1. Cut out a hole 4 5/8” in the existing ceiling. Note: 1” inch maximum ceiling thickness. Fig.1 2. Pull the ceiling wire through the hole. Fig.2 3. Remove fixture junction box door and connect fixture wires to building wires: insert each supply wire into appropriate junction box connector. This fixture features electronic low voltage (ELV) or 0-10V dimming capabilities. To utilize ELV, wire black (line hot) and white (line neutral) in accordance to dimmer specifications. To utilize 0-10V dimming, wire purple (dim+), gray (dim -), black (line hot), white (line neutral) in accordance to dimmer specifications. Green fixture wire to ground. Fig.3 Place all wiring and connectors back in junction box and replace the junction box’s cover. 4. Place all wiring and connectors back in wiring box and replace junction box door. Fig.4
Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MARCH 13, 2018 8:48 AM 1
INSTALLATION INSTRUCTION Aether 3.5” IC Remodel Housing HR-3LED-R15A HOUSING INSTALLATION: 5. Push the housing up through the hole. Fig.5 6. Push clips to secure the fixture. Fig.6. 7. Install light engine into the housing by rotating it clockwise onto stud. Fig.7 Connect light engine and housing power connectors, push the connectors into the housing. Fig.8 8. Raise the trim to housing, depress trim spring clips and push the trim assembly up until the trim ring is flush to the ceiling. Fig.8
A Pop-up Window will appear as below. (Default : COM1/9600) ... If the display reads 'FM 87.5MHZ' the re-set was completed successfully. If not repeat the steps.
(ie moisture-proof polyurethane). Important! Ensure you do not cut through the toekick below. Important! Ensure you do not cut through the toekick below.
44 Harbor Park Drive ... Connect the driver input/output wire to junction box wires as shown in Fig. 2, making sure that all wire connectors (D1) are secured.
VEHICLE LIFT LOCATIONS . .... Electric components . ..... Turbo control system preparation. ..... Before connecting the power wiring to the battery, check the ...
space that you are working on. WARNING: Risk of electric shock ... The Mounting Stake requires approximately a one (1) square foot hole to facilitate installation. The excavated should be approximately 14” deep, depending on your local code ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”.
... company's continuous improvement program. MAy, 2014 ... junction box (F1) using the junction box screws (B1). The side of the mounting plate marked “GND”.
MAy, 2014. INSTALLATION INSTRUCTION. Elemental - dwelLED ... (F1) using the junction box screws (B1).The side of the mounting plate marked “GND” must ...
To eliminate the risk of burns or fire by reaching over the .... Specified Rating of Power Supply. Cord Kit and Circuit. Protection. 120/240 Volts. 120/208 Volts.
menu and select "Restore Module Config-New ECU". ... Input the PCM engineering number, enter the first (4) digits then select the box at the end of the.
debidamente. Repita el mismo procedimiento con los cables negros. Paso 5 Conecte el cable de cobre de puesta en tierra de la caja de cableado con el cable.
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”.
... design of our products at any time as part of the company's continuous improvement program. ... Turn the lock switch to unlock position and circuit selection.
44 Harbor Park Drive • Port Washington, NY 11050. Phone (516) 515.5000 • Fax (516) 515.5050. Western Distribution Center. 1750 Archibald Ave • Ontario, CA ...
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. • Go to the main fuse box, ...
SAFETY INSTRUCTION. IMPORTANT: NEVER attempt any work without shutting off the electricity. • Read all instructions before installing. • System is intended ...
MAy, 2014. WARNING. IMPORTANT: ... plate (F1) by rotating the fixture frame. (G1) counter-clockwise. ... Secure the mounting plate (F1) to the junction box (E1) ...