This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from personä»s body in normal use position. ?Coã» ...
2 nov. 2015 - (2) this device must accept any interference received, including ... cause harmful interference to radio or television reception, which can be ...
14 août 2017 - Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et. (2) l'u
The device under test is manufactured by the grantee (Continental Corporation) and sold as an. OEM product. Per 47 CFR 2.909, 2.927, 2.931, 2.1033, 15.15(b) etcâ¦, the grantee must ensure the end-user has all applicable / appropriate operating instr
radioélectrique aux autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication réussie. This radio
Make sure the power door locks to confirm you are in the programming mode. 7) Press the LOCK ... button to confirm that the system has accepted the remote.
Important Note: To comply with the FCC/IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjuncti
Programming Instructions: 1) Turn vehicle ignition key to ON position, without starting engine (Key-On Engine-Off - Position "1"). 2) Insert Programmer into OBD connector DLC port ( - located under steering column, near pedals). Green LED should turn
The term âIC:â before the radio certification number only signifies that Industry Canada technical specifications were met. FCC ID: MRXTMS5. IC: 2546A-TMS5.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and. (2) this device must accept any interference received, including interference that may
continued FCC and Industry Canada regulatory compliance. ... This device complies with Part 15 of the FCC Rules and with Licence exempt RSS standards of.
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. WARNING: Changes or modifications not expressively approved by the party responsible for co
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installati
FCC CAUTION. The transmitter for the remote keyless. â¡Locking the doors. ã»Danger of explosion if battery is incorrectly. Changes or modification not expressly entry system is located inside the key head. Press the " " button to lock all doors and
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the rece
18 août 2015 - This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of ... equipment does cause harmful interference to radio or television reception, which can be determined by ... Over
3 nov. 2014 - This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction ...
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will n
The power door locks will cycle when you have successfully entered ... If programming has failed, repeat this procedure from the beginning. ... Changes or modifications not expressly approved by Dorman Products Inc. could void the user's ...
